Answer / bapu

it is root mean square value.(ie)take one resister give
the supply(A.C) it will produce the some heat and give the
D.C supply to the same resistance the heat will
produce.while give the D.C supply it would producethe same
heat as in A.c supply that time the D.C cuurent value shows
the r.m.s. vlue of A.c current.

Answer / nimish suchak

it is a Root Mean Square Value. it is also known as
effective value. In D.C. supply value of current is
constant so we can easily find the effective value of
current but in A.C. supply current is not constant. so to
find the efective value we taking reference Heat. it means
it is that value of D.C. current which when flowing through
the circuit produces the same amount of heat as produced by
A.C. current in same circuit in same time.

Answer / panks

root mean square

Answer / ram

consider a resistor of r ohms.give ac supply of v1 volts to
it for a time period of t seconds.due to the current
flowing through it the resistor will produce some heat q1
joules.
then the rms value of v1 is the dc voltage required to
produce q1 joules in the same time t seconds in the
resistor r ohm.

Answer / lambert

Root mean square or rms value of ac is the dc equiivalent
which when flow through a unit resistance produce the same
amount of heat produced by the dc current. It is 0.707
TIMES THE MAXIMUM VALUE.

Answer / rahul r

r.m.s value of a quantity is the root.mean.square value of it.


"Root mean square or rms value of ac" is the dc equiivalent
which when flow through a unit resistance produce the same
amount of heat produced by the dc current. It is 0.707
TIMES THE MAXIMUM VALUE.

Answer / vincent omwikha

ROOT MEAN SQUARE VALUE is the value of DC current that will
give the same heat as AC when allowed to flow in a cct for
a stated period of time.

Answer / general

The root mean square value of alternating current is equal
to the value of the direct current which, flowing through a
resistance, produces the same heating effect in the
resistance as the alternating current does.

Answer / aqeeb

it is root mean square value.(ie)take one resister give
the supply(A.C) it will produce the some heat and give the
D.C supply to the same resistance the heat will
produce.while give the D.C supply it would producethe same
heat as in A.c supply that time the D.C cuurent value shows
the r.m.s. vlue of A.c current.

Answer / guest

root mean square

what should be the air clearence between phase to phase, phase to earth in Medium voltage switchgear for 3.3kv,6.6kv,11kv,22kv and 33kv? Which is to be referred for this?

1 Answers   DLF, Sanmar, SEC,

what is the formula to convert from KVAr to current?

1 Answers   Halcrow International Partnership,

What is the effect of positive feedback on stability of the system?

0 Answers  

How many types of timer ?which timer are used star delta feeder

1 Answers   BMM Ispat,

a solar energy installation utilizes a three phase bridge converter to feed energy into power system through a transformer of 400v/400v.the energy is collected in a bank of 400v battery and is connected to converter through a large filter choke of resistance 10ohms.1.the maximum current through the battrey will be.2.the kva rating of the input transformer is.

1 Answers   GATE,

in the farm,water tank of 8000 litter capacity situated in 12 meter above.Farm owner want to lift 7000 litter of water within 7 minute to water tank of 12 meter above.which motor having HP rating is suitable for pumping??

1 Answers   ABB, Anchor, Havells, Keltron, KSEB, L&T, vguard,

An 8 pole, 50 Hz, 3-phase IM is loaded to a poing where pull out torque will occur. The rotor resistance per phase is 0.3 ohm and motor stalls at 650 rpm. The rotor frequency at maximum torque point is A 3.33% B 4.44% C 5.55% D 6.66%

1 Answers  

At the starting of dc motor and syn.motor and induction motor high current flowing through the winding. Due to this the windings burnt out. To avoid this different types of starters are used. But incase of transformer what Will be used (At starting no emf is induced in the primary winding)?

0 Answers  

How cmd is calculated in case of energy neters

0 Answers  

What is floating voltage?

1 Answers  

What is difference between 3 point and 4 point starter

1 Answers   Genco, Kaltec, TATA,

How to find ampere on ht side for selection of cable size ???

0 Answers