Dear Sir/Madam, I am attending an interview for ETs in BHEL. I have cleared m

Dear Sir/Madam,
I am attending an interview for ETs in BHEL. I have cleared
my written test under Electronics (Instrumentation). This
is the first time I am appearing for an interview. Can any
one who has attended the interview earlier give me a clue
to face the interview.
With regards
Sindhu

Question Posted / sindhu

2 Answers
6174 Views
Siemens, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Dear Sir/Madam, I am attending an interview for ETs in BHEL. I have cleared my written test under..

Answer / matrix controls c.subramaniam

Sindhu,
For everyone everything is first time first only,
No body has experienced anything before or while birth so
be bold and confident be through in your basics dont trell
wrong answer if you dont know say dont know, try to be
smart as this age people.all the best and god bless you,.

Is This Answer Correct ?

5 Yes

3 No

Dear Sir/Madam, I am attending an interview for ETs in BHEL. I have cleared my written test under..

Answer / ramesh

http://instrumentationinterview.blogspot.com/
hi go through the above blog.maximum instrumentation question answer you can find there.

Is This Answer Correct ?

1 Yes

0 No

Post New Answer

More Instrumentation Interview Questions

what is type of protocol used in instrument field to marshalling cabinet cabel. what is the differenance between bus cabel and instrument cabel?

1 Answers Samsung,

My friend has faced this question! I don't know clearly. So please anyone give me the correct and short answer to this question? What is variable frequency drive? Types, what is star to delta? Why this arrangement necessary?

5 Answers Asian Paints, TCS,

what is hot loop check and cold loop check.

3 Answers Bapco Bahrain Petroleum Company,

What is ptw and write 3 types of ptw?

5 Answers Emco,

suppose, after calibrating a transmitter we fixed it in a process line. At live zero condition the Tx shows 4.5 mA. what should we do to make the Tx show 4 mA? If we adjust zero, will it not affect the calibration?

4 Answers ABG Shipyard,

1. How many output signals do wew have in process control? 2. Could you write down the names of the pre-commissioning and commissioning stage test instruments and explain them (more than 5 items)? 3. What is the first step to commission a transmitter on service? 4. What is RTD? 5. Find the output value in MA of a temperature transmitter (RTD Type) at 120degree celius? 6. What is the O/P signal of a pneumatic transmitter? 7. What is the O/P signal of an elctronic transmitter? 8. What is the close loop and open loon?

4 Answers

What is the SCAN time of a DCS/PLC? What is the typical value for scan time of DCS and PLC?

6 Answers Essar, Gasco, Siemens,

pls tell me whethere flame proof HMI's are available or every HMI is manufactured by considering flame proof standard.

3 Answers

Can Any body tell me about the Contact or Email id of any good Consultancy which help me to find a job in Instrumentation Field in India .I have Six years of Work Experience in the Same field.Please revert me back on shammi_gwalior@yahoo.com ?

0 Answers

what is the Difference betwee the Hart and smart series Pressure transmitter

1 Answers HPCL Mittal Pipelines Limited HMEL, Kastech Instrumentation,

why 4ma show higher zero ? i have transmiter flow renge 0-1000 m3/h but 4 ma show in monitoring 200 m3/h and 20 ma show 1000 m3/h i want when 4ma show 0 m3/h and 20ma 1000m3/h

3 Answers

how the actually positioner of control valve working? where we gave 3-15psi pressure to I/P converter where it is firstly applied ?- on I/P to positioner then what happen? is control valve operate on 3-15 psi or its bench pressure?

2 Answers

For more Instrumentation Interview Questions Click Here