Answer / shailesh taware

1 CT WITH 3 CORE
1st CORE FOR O/C & E/F PROTECTION
2nd CORE FOR METERING WITH INSULATION CLASS 0.5
3rd CORE FOR DIFFERENTIAL PROTECTION
1 PT WITH 2 CORE
1st CORE FORE O/C & E/F PROTECTION
2nd CORE FORE METERING

Answer / rakesh

3 ct for metering ,3 ct for protection,3 pt

Answer / priyadharisini

3 nos of CT/PT required

Answer / manjunath kunigal

one set of tertiary winding CT/PT is sufficient for both
metering and protection.

Answer / sandeep

3 CT/1 PT

Answer / senthil kumar

06CT and 03PT'S

Answer / k n naidu

hi,
one three phase set of PTs for both protection & metering
and one three phase set of CTs with two secondary cores one
for metering and protection are required.

Answer / mubanga mulenga

You need:

1)Inst., o/c, Metering & EF - 3 CT's

2) REF - 1 CT

3)SBEF - 1 CT

Answer / vikas chauhan

3 no CT (Double core) for 11 kv side for protection and
metering
3 no CT (Double core) for 0.433 kv side for protection and
metering
11/.110 KV 3 phase PT for 11 KV side
secondry side(.433KV side) phase directly connected for
Metering & select relays for .433 KV secondry voltage.
if you select differencial rotection
3 nos CT for Primary and 3 No CT for Secondry side and
interposing CT for Match and neutralise the current in
relay.

Answer / d ramesh

11KV side(delta)
Line side 3core CT :1No. for metering, O/C&E/F protection,
Differential protection with ICT.

0.433KV(Star)
Nuetral CTs :1core for Standby E/F 5p20
Line CTs :3core CT:1No for metering, O/C&E/F
protection,Differential protection with ICT.

1No. 1-core CT in LV nuetral of Transformer of class 5P20
for earth fault protection.

panel side in the panel itself remaining CTs can be
provided for metering, O/C&E/F, and differential cores with
ICT. In both HV panel & LV panel.

deisel generators all elcetical calculation formule's

1 Answers  

what is meant by dielectric breakdown ? where we using HV test kit & what purpose?

3 Answers   ITC Infotech,

what is meant by switch fuse unit ?

3 Answers   Thermal Powertech Corporation India Ltd TPCIL,

Draw SLD feeding from the SS up to distribution board of the load, calculate cable size, breaker sizes, and meter for the following case: Ground Floor: electric room, pump room, 5 shops, each is 15 KW First Floor: 5 shops, each is 15 KW Second Floor: showroom 30 KW Service Loads: water pump 3 KW (3ph) , fire pump 3 KW (3ph), and one DB service 12 KW (3ph).

0 Answers   FEWA, HMK,

while we select CT, why the CT ratio is divided by 5?? ex:250/5,15VA,CLASS-1 CT.Why it is divided by 5??Help me please

2 Answers  

Can clean earth cable be considered as low current cable

0 Answers  

what is hunting?

2 Answers  

WE HAVE THE DC RECTIFIER 1500A, INPUT VOLTAGE IS 3 PHASE. HOW TO CALICULATE THE LOAD? 3 PHASE SIDE EITHER dC SIDE. PLEASE SUGGEST ME

0 Answers  

Explain why inductance of the iron cored coil changes with current?

2 Answers  

What is a difference between indoor transformer and outdoor transformer of same rating

0 Answers   Suzlon,

Star Delta Diagram with full description

0 Answers   SKS Microfinance, Syscom,

What is meant by rating error prevention in breaker??

1 Answers   L&T,