Answer / yuvi

Honestly, this question does not make any sense. However, I
will try to answer to the best of my understanding.

1) I don’t have a generator.
2) Difference between manual and automated generator is
that in a manual start generator, we will have to manually
start it. In an automatic start generator, a circuit senses
that the power has failed and starts the generator
automatically using a small battery powered motor similar
to the ones that start your car. The sensing circuit can be
of a wide variety. It can be a magnetic relay or an
electronic circuit depending on the area of application.

Answer / tapas

in both Auto and Manual cases circuit diagram can be found in the Drawing of Sync panel/AMF panel. Its a selector switch by which user can select either Auto mode or Manual mode.
DG start and stop circuit has two ways to operate which can be found on drawing.
1.Manual Mode: In this mode push button start and push button stop operates DG. i.e. when power fails DG can't be started Automatically. Operator should start the DG manually.

2. Automode: PLC senses absence of Power and commands DG to start.

Answer / ferozuddin

generator wiil be function as a manual and also auto .
manual in case of when there will be no interface with the
auto transfer switch (ATS).when generator is interface with
the ATS it will work auto in case of emergency

Answer / mani0786

mannully start genset start manually & wwhen it come with a amf or ats panel it said auto genset well sir your question is out my mind but so i give it a simple sot

Answer / shyamuchary

we have 3 types
1.manual
2..auto.3.semi manual

Answer / singadurai58

Its very simple
Take an 230v auxillary contactor with 1NO POINT and 1NC POINT
One single phase connect at one side NO POINT and other end connect to contactor A1(NO VOLT COIL).A2NEUTRAL directly connected.
Positive (+) supply24 v connected at NC POINT one side and other end connected at generator starting switch .
When EB powersupply is there the contactor is on.
When EB supply cut through NC POINT the positive supply passing to the switch so the generator is on.
Its very cheap.

Answer / ponvel

manual

Is it possible to get earth resistance value"zero" Ohm practically??? If yes,which type of earthing???

9 Answers   TATA,

I am an American living in Vietnam and I have recently gotten a refrigerator from Japan and it is rated for 100 vac, but the power here is 220 so I bought a voltage stabilizer it has a 1 kva output rating. Can you please tell me what the amperage is? I'm confused and without a working fridge.

0 Answers   BSL,

what are the main differences of delta and star connection

5 Answers   Essar,

if a 3 phase induction stator has charactristic plate and have on winding inside.with the calculation of plate or dimenssion of core how one can desinge rewinding drawing.

0 Answers  

what is the use of choke on tube light fitting

37 Answers   Bhel, Dharma, HSBC, TCS,

what is F.A.P in fire alarming system?

3 Answers  

power transmission pole used one support , that only for support or earthing

0 Answers  

i) in which cases should we go for neutral and where should we go for ground? ii) in domestic supply we are getting 230v a.c.and what is the amount of current?

2 Answers  

What is the difference between DOL starter and star delta starter

0 Answers  

What is the theoretical capacity of a channel in each of the following cases? i) Bandwidth: 20KHz SNR(dB) =40 ii) Bandwidth: 200KHz SNR(dB) =06 iii) Bandwidth: 1MHz SNR(dB) =20

0 Answers   UOG,

What is NDR in HT capacitor panels.

2 Answers  

What is difference b/w fuse and breaker?

3 Answers   Jindal,