Explain about relays..
Can we give both AC and DC to the same relay...
How it is energising..
Explain its working..
Answers were Sorted based on User's Feedback
Answer / vijay
relay is nothing but contactor(no, nc), for working (coil
energise) supply we can give according to their
specification, for contact (no,nc ) we can give ac r dc but
we can not give both supply
Is This Answer Correct ? | 10 Yes | 1 No |
relay is a device to make or break circuit
we can give both a.c. & d.c. acording to type of relay
Is This Answer Correct ? | 6 Yes | 2 No |
Answer / prashant kumar , tcl
generally relay defined accordingly to ac and dc powered for
its coil , means relay coil for ac or dc. but at the contact
(NO AND NC) We can use ac or dc because these are potential
free contact from relay.
for relay energizing we can use only one power ac or dc
accordingly to its specification.
Is This Answer Correct ? | 3 Yes | 1 No |
Answer / shrinivas
relay is slightly differ by contactor. as contactor is used
wher power is more while relay is used on low power ckts
another thing is that the same relay can't use on both the
supply this is b'coz in dc only small resistance which is
coil having oppose the current wher in ac the opposition by
impedance thereby same relay can't use on botj type of
supply
Is This Answer Correct ? | 1 Yes | 0 No |
Answer / g ramakrishna
relay is the device which is used to trip the contactor when the fault occurs.it has no and nc points.by using this points it will trip the circuit.the power supply is transmitted through nc point of realy to the coil of contacter. whenever the fault occurs the nc point of realy opens the circuit and trips the circuit
Is This Answer Correct ? | 0 Yes | 2 No |
Answer / gulab chand saini
it sence any abnormal condition and react accordingaly,it
having no or nc contact for trippig the ckt
Is This Answer Correct ? | 1 Yes | 4 No |
Answer / harish
relay nothing but a electrical switch working on coil .when
supply is passed to relay energise break the connected
circuit.
Is This Answer Correct ? | 0 Yes | 6 No |
what is exact time to study dcs and plc cources
kindly sent some demo question and answer
What is the Difference between CNC and PLC
what is intools software
Why the ammonia and Nitric Acid level indicators is with millimeter ? and What is the conversion form millimeters that level indicator indicate to weight ?
What is the difference between HMI and SCADA and MMI
how micro-processor and micro controller different from architecture
3 Answers Bhushan Power Steel,
capillary type tranmitter using remote seals and capillary tubes filled with liquid of known of known density so if you wanna callibrate it just close block valve just before capilary @ high side & connect druck apply it's calibrated range pressure as normal calibration ensure low side block valve must be closed & if you asking commissioning so this is not a DP type pressure tx so simple if you wanna put in servie this tx just open high side block valve & than low side block same way i do it but still transmitter showing -13 ma.just tell me what i want to do ?
Describe how to calibrate various types of instruments and transmitters using ISA industrial consensus standard techniques.
Level in tank under vacuum (Ex: Condensate Tank of Power Plant)is measured using D. P. type level transmitter. Tank is subjected to vacuum of 755mmHg. Is it possible to fill wet leg ( i.e. leg connected to top of vessel with low point of D. P. xmtr) with water?. Are there chances of water getting sucked under vacuum? if yes, what is the solution?
Can we use thermocouple in generator of power station replace RTD(pt 100)? if we don't have any place for use RTD.
where uses EXe /EXd/Exo/Exn/Exp/Exq/EXia