Describe the basis on which alarms should be generated and how their associate

Describe the basis on which alarms should be generated and how
their associated priority is determined

Question Posted / slyabi

3 Answers
5175 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Describe the basis on which alarms should be generated and how their associated priority is determ..

Answer / sumith

alarms are generated on interlock basis.
safety interlock is given first priority.

Is This Answer Correct ?

2 Yes

0 No

Describe the basis on which alarms should be generated and how their associated priority is determ..

Answer / chandrasekarapandian

For this issue take a water tank on which our Level
Transmitter is measuring level in meters Or any required
unit but generally 4 to 20 mA --> 0 to 100 % . Now we can
set 90% as HIGH and 95% as HIGH HIGH . Through by means of
proper alarm setting we can automate our process
comfortably . Alarm priorities depend on the process
requirement. In this process as HIGH alarm blinks that
gives just a warning, But HIGH HIGH alarm blinks that will
need to close the inlet of water tank to avoid overflow.

Is This Answer Correct ?

1 Yes

0 No

Describe the basis on which alarms should be generated and how their associated priority is determ..

Answer / vinod hepat

Alarm should be generated for all the values which distrub
you process & alarm should be set at such a value that
operator get time to take corrective action.

alarm which hamper ur process,safety or equipment badly
should be given high priority.

Is This Answer Correct ?

1 Yes

0 No

Post New Answer

More Instrumentation Interview Questions

field bus transmitter calibration procedure tell me

0 Answers BAP,

What are all the type of vibration measurement measuring in turbine, what is the output of vibration sensor.

3 Answers

What will the new flow factor if D/P Transmitter is RE-RANGED from 25" WC to 50" WC

3 Answers ADMA OPCO,

We are using Rosemount 5400 series Radar Level Transmitters in all types of Sump Applications having oily water hdrocarbon petrochemical nature. What we are facing the problem frequently is that always getting reading frezzed at some value. If we do power recycling , sometimes it is working . then making same freezing problem. If anybody faced before such type of problem and also having solution , Please give the answer.

0 Answers Sabic,

Paper Details: company -- Hindustan Copper Limited post -- GET 2008 Date -- 03.08.2008 Dept.-- Electronics?Instrumentation Aptitude -- 70 Technical-- 80 Total Time -- 2hr 30min I have listed the question I could able to remember 1. BCD equivalent of 43 2. value of K for stability of a system from a given equation 3. transformer connection for darlington connection 4. damping of balastic galvanometer 5. advantage of chart-pen recorder over CRo 6. CRO - how to change bandwidth 7. questions on CRO construction 8. reverse saturation current of si diode 9. advantage of wire wound resistance over carbon resistance 10. core material for a small coil 11. max fanout-- TTL/ECL/CMOS/MOS 12. component of resistance of monolithic IC 13. functions of capacitors in multivibrators 14. to change a sawtooth signal into a square wave we use-- schmit trigger/ schottkey diode/ zener diode 15. relation b/w á & â in transistor ckt 16. function of SiO2 layer in fabrication 17. 3 questions on ODD MAN OUT

2 Answers HCL, L&T,

1.what is the role of proportional comtroller in pid controller?2.How do u calibrate the control valve?

3 Answers Bently, IOCL,

what is maxdna ?. explain about the software details.

0 Answers

Why trim span ? How?

0 Answers

what is the input of digital counter during the the calibration time?

0 Answers

How to calibrate the control valve.

1 Answers

Can Any body tell me how to check Modbus Settings in ER300N L&T trivector meter?

0 Answers

whatis range of marcury filled tempereture gague

0 Answers Dr Reddys,

For more Instrumentation Interview Questions Click Here