Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


i install a DP transmitter of Faugi on drum level of boiler
but i face a problem in it when i engergize the transmitter
the meter shows 0 or 100% no variation in it.the distance
of two points is 19.5 inches, i am in trouble please
suggest me what can i do it's very urgent Please reply me
as soon as possible

Best regards

ikraam haider

Answers were Sorted based on User's Feedback



i install a DP transmitter of Faugi on drum level of boiler but i face a problem in it when i enge..

Answer / s.arunraja

Hello Dear first check the Calibration Range of Transmitter,
Range should be -xxx(495) to 0 mmwc. for 0 mmwc 20 mA will
be come.when you fill the water in condensate pot 4mA wii
be come because it's closed vessels

Regards
S.Arun Raja

Is This Answer Correct ?    4 Yes 0 No

i install a DP transmitter of Faugi on drum level of boiler but i face a problem in it when i enge..

Answer / sagar khandekar

First check
range of
transmitter if
ok then check
+ve & -ve side
of line if again
ok then check
4-20 mA current
means
calibration if
again ok then
check program
and check scale
range. Follow
these step 100%
confirm solve ur
prblm.

Is This Answer Correct ?    2 Yes 0 No

i install a DP transmitter of Faugi on drum level of boiler but i face a problem in it when i enge..

Answer / r.murugan

Dear haider
your transmitter calibration is perfect before charging the tramsmitter you have to fill the water in the condensing pot at low side of the tranmitter

boiler is shutdown condition please confirm DRUM VENT ISOLATION VALVES ARE OPEN

IF DRUM VENT ISOLATION VALVES ARE CLOSE YOU WILL NOT GET CORRECT READING

Is This Answer Correct ?    1 Yes 0 No

i install a DP transmitter of Faugi on drum level of boiler but i face a problem in it when i enge..

Answer / ikraamh5

engineering level

Is This Answer Correct ?    0 Yes 1 No

i install a DP transmitter of Faugi on drum level of boiler but i face a problem in it when i enge..

Answer / ashish mahadik

U have to apply WET LEg method for Differental Pressure
type level mesurmetnt.Keep ur wet leg(Lo side of tx always
filled with condensed water.
Put the range in tx.-19.5 inches of WC to 0 inches of WC.
see the result but make sure that ur wet leg should always
filled with water.otherwise ur tx l go to saturation and
give u contunous 20 mamp that is level is full.

Is This Answer Correct ?    1 Yes 2 No

Post New Answer

More Instrumentation Interview Questions

explain key exchanges in all security modes WPA,WPA2,TLS?

0 Answers  


what is difference between RTD , thermo couple and thermistor in general ?? (except temperature co-efficient )

5 Answers   Bilt,


Can we get the outpot in c without using getch fiction? Answer is yes but output will stay on display 4 only few second.... But can we get output without using getch and also output will hold on the display...?

1 Answers  


whatis range of marcury filled tempereture gague

0 Answers   Dr Reddys,


why 4 to 20 ma used at 0 set

2 Answers   Borouge, Yokogawa,


1. How can leveltrol be installed in steam drum for measuring the level of steam drum?

1 Answers   Fischer,


How servomotor controls throttle valve of TURBINE?

0 Answers  


what is the difference between active and passive loop ?

8 Answers  


What is the purpose of bypass valve across AS valve.

0 Answers   ADMA OPCO,


What are the type of bonnets in the control valves?

0 Answers   CCIE,


how can we tune a PID. If it is by zeiger nichols method..please explain briefly with help of an example.

0 Answers   KNPC,


Can I calibrate the Electromagnetic Flow Meter on line and How.

0 Answers   SEWA,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)