why compression strenth of concrete is tested with a cube of size 150x150x150

Categories >> Engineering >> Civil Engineering
Suggest New Category

why compression strenth of concrete is tested with a cube of
size 150x150x150 mm ?

Question Posted / anish kumar

5 Answers
15063 Views
Gammon, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

why compression strenth of concrete is tested with a cube of size 150x150x150 mm ?..

Answer / souagata bangal

In 150x150x150mm cube the dimension 150mm is match with the pressure plate dimension.If it is less than 150mm the total pressure distribution is not as per spesification and it will show more than the cube value.If the dimension is grater than 150 mm ,the pressure distribution will not to the whole surface of the cube.

Is This Answer Correct ?

27 Yes

5 No

why compression strenth of concrete is tested with a cube of size 150x150x150 mm ?..

Answer / sjtbehera

Because as per IS standard the compressive strength is
taken as per these specimen

Is This Answer Correct ?

29 Yes

9 No

why compression strenth of concrete is tested with a cube of size 150x150x150 mm ?..

Answer / sanjay tewatia

the test on this dimension is done because it is specified in is coding system, and also because the varieing pressure of concert will not rises in less then the 100mm area and it will not give the actual positioning of the spreading area and to varies the whole strength of each substance mixed in it to give its full volume

Is This Answer Correct ?

7 Yes

5 No

why compression strenth of concrete is tested with a cube of size 150x150x150 mm ?..

Answer / deepak baviskar

Basically, the force supplied by a
concrete compression machine is a
definite value. For normal concrete
strength application, say below 50MPa,
the stress produced by a
150mmx150mmx150mm cube is
sufficient for the machine to crush the
concrete sample.

Is This Answer Correct ?

1 Yes

1 No

why compression strenth of concrete is tested with a cube of size 150x150x150 mm ?..

Answer / h.k.chanchal

In RCC like M15,M20 suffix is result of compressive
strength of 150x150x150 mm cube sample.

Is This Answer Correct ?

9 Yes

16 No

Post New Answer

More Civil Engineering Interview Questions

Design a cantilever type retaining wall to retain sand for 4m above the ground. The sand fall slopes at the rate of 1 vertical to 2 horizontal. The weight of sand is 18000 N/m3, the angle of repose being 30. The safe bearing capacity of the soil is 200 kn/m2 at 1/25m below the ground level. Use m 15 concrete mix.

0 Answers College School Exams Tests,

Define What are the reasons for geotechnical site investigations in Uganda?

0 Answers

what is minimum dimension for the kitchen & bed room

7 Answers

What do we mean by partial moment release ??

0 Answers

How do piles bear loads

3 Answers

how the take measurement at column and beam junction

1 Answers DMRC,

11. What was the reason for you to quit your previous job?

5 Answers

What does a construction cost covers and what does not?

0 Answers

Can anyone tell me the salary and job profile of transportation engineers/transport engineer?

1 Answers

how much quantity of cement and sand required for construction of 10 cum brick work( Brick size 3"*4"*9"(Standard size ) an d for 10 cum construction of SSM (Size stone masonary) with Cm 1:6 for both.

11 Answers GRC, KEC, L&T, Techno Electric and Engineering, UPENN,

# 1. Water observation capacity (MAximum)of Solid bricks # 2. Minimum Crushing Strength of Solid Blocks.

4 Answers Brigade,

what will be the total emoluments for deputy surveyor in APPSC in the payband of ( 9460-27600). please give me the detailed information step wise?

0 Answers APPSC,

For more Civil Engineering Interview Questions Click Here