why current coil has less number of turns compared to
pressure coil?
Answers were Sorted based on User's Feedback
Answer / vinod singh
current coil is connected in series so that its resistance
should be as minimum as possible otherwise there will be
voltage drop and power loss during normal working condition.
Is This Answer Correct ? | 53 Yes | 6 No |
Answer / anindita
current coil is connected in series with the load whereas
pressure coil is connected parallel to the supply, that is
pressure coil is connected across the voltage source.
current coil have lesser number of turns than the pressure
coil so that the impedance of the pressure coil increases
and it draws minimum current from the circuit,causing lesser
error in the reading.
Is This Answer Correct ? | 22 Yes | 6 No |
Answer / kundanmalani1990
bcz the CT are connected to the series in supply line so
that high current pass through the line and high current to
absorbers to CT so current coil has less number of turns
compared to pressure coil !!!!
Is This Answer Correct ? | 12 Yes | 11 No |
Answer / ansuman
current coil have to measure current ; to achieve it less resistance is given by providing less number of turns in current coil.
Is This Answer Correct ? | 3 Yes | 2 No |
Answer / raju kumar
this is because,current supplied to the load may be more and more and wattmeter may get current reading of power supplied
Is This Answer Correct ? | 2 Yes | 3 No |
Answer / raj kumar
Current coil connected in series with the load.in series circuit current is same and voltage different.if we are increasing the number of turns in the current coil as like pressure coil number of turns.
First load current only passes through the current coil because series circuit.so current increases automatically voltage drop will increase.so error will occur.it will not show the correct reading.
Is This Answer Correct ? | 1 Yes | 2 No |
Answer / nithi
IF CURRENT COIL IS PROVIDED WITH MORE NO. OF TURNS,THEN IT
WILL DROP MORE VOLTAGE ,AS IT IS CONNECTED IN SERIES WITH
THE LOAD.
Is This Answer Correct ? | 7 Yes | 9 No |
Answer / mr. utsav jain
bcz current coil connected in series and the pressure of the current coil is very high so it will produce large voltage drops.
in parallel condition obtain the high voltage large no of turns.
Is This Answer Correct ? | 2 Yes | 4 No |
what is the different between second harmonics and third harmonics ?
control wiring purpose,standards, ferrule code standard, interlock, schematic, symbol
I need to calculate the Battery bank back up for below configuration:- UPS - 120 KVA Battery Bank - 200Ah Volt of each cell - 12 V Total No of cell - 34 No's Can you please help me to get the battery back up time for above configuration...? along with formula
what is difference between low voltage and high voltage
what are the condition that makes hooter blow?
sir, in a industry present pf is 0.54 pf 25hp power is there its want improve 0.9 pf. which suitable capacity capacitor is suitable please inform me.
what's producer of XLPE cable laying in undergroung
we have require a Motor (1500kW, 6.6kV, 50Hz) which shall operate at 1500rpm during 30min and after it shall run on 500rpm during 15min. The same cycle shall be repetitive during the whole working days. Which method is best and economic to achieve such type of task. VFD, VVFD, Pole changing motor etc.
What is IDMT? What is the principle
How will you calculate the correct KWH value if your CT is 600/5 and your KWH meter is rated for 100/5
what is difference between inductive and reactiveload?
i heard that power factor(PF) is the main concern for industries, if they are maintaining PF around 0.6 they will be fined for that. now the question is, how can they improve the PF ranging between 0.9 to 0.95 which is safe for them i,e escaping from the fine?