Answer / emvprasad

PT 100 RTD means Resistance temperature detector(RTD) of
platinum with 100 ohms resistance at zero degree centigrade.

Answer / blloyd

Pt100 RTD:

Pt = Platinum
100 = 100 Ohms at 0 degrees Centigrade
RTD = Resistance Temperature Detector

Answer / guest

platinum 100 type rtd. 100 stands for resistance(i.e 100
ohms).We set 0 temperature for resi 100 ex range 0 to
200degcel. then 0 degree is for 100 ohm resistance.(min set
value)

Answer / mhax papio

Pt100 means PT is platinum material used in the sensor of
the Resistance Temperature Detector.100 means the
resistance of the sensor is 100 ohms at 0 deg C

Answer / ayaz

upper all answer is minor wrong
RTD=RESISTANCE TEMPERATURE DETECTOR
PT= PLATINUM this is material we use in RTD
1OO= 100 ohm 
 AND PT100= PLATINUM IS Odeg C at 100 ohm

Answer / rashid hussain

It is type of RTD (Resistance Temperature Dedector )
Which is made of platinum metal and gives 100ohm output at 0 Degree temperature...

Answer / ganesh raut

Pt100 means platinum metals used to measure temp. In this we measure 100 ohm at 0 degree celcius

Answer / faiyaz ahmad

pt 100 means 100 ohms of resistance 0 degree Celsius
pt means platinum.

in the construction field why hook up s.s.tubing for transmitter using upto 6mtrs of closed loop, but y not open loop nomore restriction

5 Answers   Sabic,

please anyone suggest me some good intools training institutes with their place and contact nos.

1 Answers   ABB, Thermax,

What is an instrumentation amplifier? How is it better than a differential amplifier when handling outputs from a wheatstone's bridge?

2 Answers   Honeywell,

can any one give me the cost price of yokogawa & rosemount transmitters

4 Answers  

[ MITUTOYO / TESA / KUMAUN / MAHR / BRITOOL / TOHNICHY / DIATEST-GERMANY / IMADA / TECKLOK / SYLVAC /ADITYA=ACCURATE / BAKER/ CRYSTAL / FLUKE-RAYTEK ETC. 5.=SUPPLY= VERNIER CALIPERS / MICROMETERS / HEIGHTGAUGES / SLIPGAGE / BORE DIAL GAUGES / MEASURING PINS / TORQUE WRENCHES / GAUGES.. PLUGGAUGES / RINGGAUGES / SHORE A / D HARDNESS TESTERS / DIAL THICKNESS GAUGE / FEELER GAUGES / ELECTRONIC COMPARATORS WITH PROBES / DFTMETERS / SURFACE ROUGHNESS TESTERS / DIGITAL= COATING THICKNESS METERS / PROFILE PROJECTORS /.. WE ARE ALSO DEAL IN == DIGITAL TACHOMETERS / =MULTIMETERS! / VIBRATION METERS / MEGERS- INSULATION METERS / =TE! MPRATURE INDICATORS / SOUND-LEVEL METERS / ETC... =AGENCY- FLUKE- RAYTEK.. MECO....LUTRON...KYORITSU....RION

0 Answers  

what is difference between total flow and flow rate in general ?? explain it with daily life example.

3 Answers   GNFC,

Please explain about FAT? What is the difference between FAT and SAT?

6 Answers   IBM,

A DP transmitter is used to measure the level of an open tank. The drain line of the tank is connected to a control valve, and is configured as, if the level of the tank is 90% the valve should get open 10%. And if the tank level is 10%, the valve should get open 90%. Draw wiring diagram and explain how to configure DP transmitter and control valve using HART communicator. If the span error at output is 1%, what will be the %opening of the control valve at 60% level of the tank?

0 Answers  

steps for installing orifice plate?

0 Answers   Bhushan Power Steel,

which type signal come control valve

6 Answers  

Which tank weighing system is better to install (Accuracy point of view) 1) Tank weighing system with 3 load cell or 2) Tank weighing system with 4 Load cell

0 Answers  

In closed loop control there are several “blocks” used to show the interactions between the process and the control system. These blocks are referred to as the “process” and the “controller.” Describe the relationship between these two blocks when creating a well tuned control loop.

1 Answers