Why in celling fan stator are rotatig while rotor are steday
Answers were Sorted based on User's Feedback
Answer / anubhav
Actually equal and opposite torque acts on both stator and
rotor......but in ceiling fan rotor is fixed that's why it
cant rotor,so what rotates is stator or the outer part of
the machine.
Another interesting thing to observe-why ceiling fan
rotates in clockwise direction while table fan in
anticlockwise direction.......because in table fan the inner
part is rotating (i.e. rotor is rotating).
Is This Answer Correct ? | 23 Yes | 3 No |
Answer / vasu
the question it self is wrong
what rotates is rotor and what does not is stator
Is This Answer Correct ? | 11 Yes | 9 No |
Answer / br
Answer 5 is good ...there is more to it ....practical
construction of ceiling fan ----> you cannot attach fixed
supply wires to rotating part ( simplicity of construction
)hence they are attached to ROTOR ( middle stable part in
case).....Fan Blades must be attached to rotating parts but
cannot be attached to middle shaft as it contain Ball
bearing for support at that place.Ball bearing can suport
rotation but not lateral tension ....Therefore
1. Supply is attached to stable part so that connection is easy.
2. Blade are attached to body , so body ( lower one) must be
rotating.
Technically ...ROTOR and stator are named based on their
movement ability. Supply can be attached to ANY ONE of them
based on your practical suitability.
BR
Is This Answer Correct ? | 1 Yes | 1 No |
Answer / suresh apgenco
there is no fixed deal for the rotation, which ever is
having chance for rotation that will rotate.
Is This Answer Correct ? | 1 Yes | 4 No |
Answer / neeta
the answer to your qstn is......rotatin field type construction is used in ceiling fan dat hav many advantages in case of high power machines
Is This Answer Correct ? | 1 Yes | 5 No |
How to test transformer
1. for eg, capacitor is used for many purposes(it act as filter, oscillator, bypass capacitor, memory storage etc...) 2. Please tell me some example circuits for different uses of capacitor( whenever and whereever and however we used capacitor as a filter, oscillator tuning etc..) 3. similarly for inductor and resistors(it act as what?) and when and how we want to act as like that?, and how we can used these components depends upon our requirments with example circuits and explanation? design to act as these components depends
how much current and power in watts can be carry by 2.5^2mm cu wire and 4 core 10^2mm Al cable?
In single phase ac ups supply when current is measured with tong tester neutral current is found more than phase current.What is the reason?
i want to know about psu exam eligibility critaria?
can a rotating machine give the DC output without commutator? if yes, how? if no, why?
a voltmeter shows 100v..wat is to be done to make it read 150v.
THE 40 MW OF POWER FOR 220 V III PHASE POWER CONNECTION REQUIRES HOW MANY KVA POWEER REQUIREMENTS
7 Answers Chartered Accountant,
what are the basic insulation levels & what its Unit
Usually in the L & T make MCC feeders' power circuit,we have BMR after the MAIN CONTACTOR.,can we interchange their position, keeping the control logic same???
WHAT SHOULD BE THE BEST CURRENT RATINGS (PRIMARY / SECONDARY)FOR A CT INSTALLED AT THE INCOMING 11KV PANE? WILL IT BE CALCULATED ON THE BASES OF MAXIMUM DEMANT VALUE OR ON SUM OF ALL TRANSFORMER'S KVA? NOMALLY MAX DEMAND REPRESENT THE MAXIMUM OPERATING LOAD OF THE PLANT AND TOTAL KVA OF (SAY 5 NUMBERS TRANSFORMERS) REPRESENT THE CONNECTED LOAD. WHICH i.e. MAX DEMAND KVA OR CONNECTED KVA ARE BETTER TO USE FOR CT CURRENT CALCULATION? PLEASE ANSWER.
what is sustainable current of any conductors . a bare busbar or pvc cable has different sustainable current .