Answer / premkumar

can u check whether its DHCP or Static ip Address?

If its static means change in dhcp. try this.

Answer / jitendera

hi shyam sorry for late reply.this problem is quite simple and there is no any fault with u r cable so donot go towrds the wrong direction
look this problem occurs due to high trafic on the partucal port.
How
look when ever you are removing the cable and tested through lan cable the problem get solved for 2to 3hr hrs right?
the cause is that when ever there is high trafic on the prticular interface the switch port get block when you reomve the cable all tarfic drop and it start working fine.

now what is the soulution-
there are some causes for this type of prob

take these steps
virus on the particular system
(1) the hight trafic might be due to virus so please scan the system with good antivirus.
(2)looping may be cause(in some cases)-
check all the cable be assure that there is no any cable looped in the network and also veryfied that stp is runing over the switch if it is not running enable the stp on the switch
(3)port are not functing well?
change the switch port for the sytem and let see
(4) if this all is not working take another 8 port switch/hub and connect it to the layer2 switch and then connect the system cable from the 8 port switch/hub
This might be solve the issue or else it will give u time to think and me too

this is some defalut cause of that prob check it out and let me know

Answer / shyam

Thanks Jitendera I was waiting Ur replay only. Tell me one think can STP work on layer2 switch also. In layer 3 we can check STP and block, forward port but in layer 2 can we I don’t think so. Yes u r right it may be traffic jam. But how I resolve that my that switch port is working fine there are on problem in that switch port. I have changed also. I don’t understand what the problem is. And u give me ur mail id if u have yahoo messenger id..Thanks for answer but plz find more and provide me mail id also if u can

Answer / lokesh

reset the network adaptor for partular system

Answer / sunil

check that there is not an lose contact.or reinstall the lan
driver

What is cam?

0 Answers  

What is a characteristic of Store and Forward switches? A.) They forward the frame before it is completely read. B.) They work at wire speed. C.) They are the same a Cut-Through switching. D.) They read the entire frame and check CRC before forwarding. E.) They decrease latency.

1 Answers  

Hi friend , This is Harekrushna . I have been tried for netsim keygen but i could not download this crack file .if it download then showes the writer protect error. PLEASE sugest me what isthe soluation. or any other software avalibe for pratics the network .

2 Answers   PCS,

Can you give an overview of various components in IPSec?

0 Answers   CCIE,

Identify the type of hardware required to connect a Token ring network to an Ethernet network? A.) Repeater B.) TR-Enet C.) Router D.) Token Ring to Ethernet translation hub

1 Answers  

Which statement about the data link connection identifier (DLCI) is true? A. It is a number that identifies a local virtual circuit in a Frame Relay network B. It is a signaling standard between the CIDE device and the Frame Relay switch C. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay Cloud D. It is the Maximum number of uncommitted bits that the Frame Relay switch will attempt to transfer beyond the Committed Information Rate (CIP)

2 Answers  

When setting up a frame-relay network between a Cisco router and a non-Cisco router, what encapsulation type should you use? A.) SAP B.) CISCO C.) IANA D.) Apollo E.) IETF F.) Q933A

2 Answers  

Scenario: You created 2 access-lists for controlling telnet about a year ago, and bound one of them to Serial 0. You can't remember which access-list you used. Which command lets you see all access-lists on Serial 0 for telnet? A.) show access-list B.) show ip int s0 C.) show access-list telnet D.) show telnet access-list E.) show access-list s0 F.) show int s0

2 Answers  

What is the Network Layer of the OSI responsible for? A.) Bridging B.) Routing packets through an internetwork C.) Regenerating the digital signal D.) Gateway services

3 Answers  

If you are in IOS user mode, which command do you use to enter the privileged mode? A. Set B. Enable C. Configure D. Privileges

2 Answers  

CCNA question and answer only for networking.

0 Answers  

what is diffrence between circit switching and packet switching

1 Answers   HCL, Volvo,