Which command successfully pings an individual IP address? A. Router> ping 192.5.5.0 B. Router# ping 192.5.5.30 C. Router> ping 192.5.5.256 D. Router# ping 192.5.5.255

2 Answers  

---

Identify the command to configure the router to boot from an alternate IOS located in flash? A.) boot system flash IOS.exe B.) boot system tftp IOS.exe 172.16.5.1 C.) boot system alternate IOS.exe D.) boot system rom IOS.exe

1 Answers  

---

What is the difference between static ip addressing and dynamic ip addressing?

0 Answers  

---

As the system administrator, you type "ppp authentication chap pap secret". Which authentication method is used first in setting up a session? A. secret B. PAP C. CHAP D. PPP/SLIP

1 Answers  

---

Which processes does TCP, but not UDP, use? A. Windowing B. Acknowledgements C. Source Port D. Destination Port

2 Answers   Lucent,

---

What are the ranges of private ips?

0 Answers  

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

1 Answers  

---

What is the routing metric used by RIP? A.) Route poisoning B.) Split horizon C.) Hop Count D.) TTL

4 Answers   jetking, Tata Motors,

---

What is the Broadcast MAC Address?

3 Answers   Avaya, Cisco,

---

What is the routing metric used by RIP? A.) Route poisoning B.) Split horizon C.) Hop Count D.) TTL

1 Answers  

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

Which of the following are valid Cisco encapsulation type names? A.) arpa = IPX Ethernet B.) novell-ether = IPX Ethernet_802.3 C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring D.) novell-fddi = IPX Fddi_Raw E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring F.) hdlc = HDLC on serial interfaces

1 Answers  

---