Interested to Buy Any Domain ? << Click Here >> for more details...
I am facing one problem in my layer 2 switch I don’t know
the problem is on switch side or client side. The problem is
some PC (not all) are stop participate in LAN they don’t
send or recd. Packet from switch and if I check RJ45 (with
LAN tester)from PC side the packet and 8 pin wire is working
fine and after that process of LAN tester I plug RJ 45 in PC
now PC start recd/ send packets what is the problem I don’t
understand even client side no virus found RJ45 is ok and
switch has no problem bcoz other PC is working fine Cable
(cat 5 ) is also fine bcoz I didn’t crimp again just check
in LAN tester and start working fine. Plz any one solve this
matter. And after lan tester process pc is working fine and
after 2 or 3 hour it again start same problem and again same
process lan tester I have used
- 5 Answers
- 8108 Views
- I also Faced
- E-Mail Answers
Answer Posted / jitendera
hi shyam sorry for late reply.this problem is quite simple and there is no any fault with u r cable so donot go towrds the wrong direction
look this problem occurs due to high trafic on the partucal port.
How
look when ever you are removing the cable and tested through lan cable the problem get solved for 2to 3hr hrs right?
the cause is that when ever there is high trafic on the prticular interface the switch port get block when you reomve the cable all tarfic drop and it start working fine.
now what is the soulution-
there are some causes for this type of prob
take these steps
virus on the particular system
(1) the hight trafic might be due to virus so please scan the system with good antivirus.
(2)looping may be cause(in some cases)-
check all the cable be assure that there is no any cable looped in the network and also veryfied that stp is runing over the switch if it is not running enable the stp on the switch
(3)port are not functing well?
change the switch port for the sytem and let see
(4) if this all is not working take another 8 port switch/hub and connect it to the layer2 switch and then connect the system cable from the 8 port switch/hub
This might be solve the issue or else it will give u time to think and me too
this is some defalut cause of that prob check it out and let me know
| Is This Answer Correct ? | 2 Yes | 0 No |
Post New Answer View All Answers
What is the difference between cross cable and straight cable?
Which mode called privilege mode?
When we use interface mode?
What is mtu and what is its size for transmission?
What are the advantages of a layered model in the networking industry?
Which protocol switch use for filling its mac-table?
On which base distance vector choose best path?
Define the virtual path?
What is the checksum?
Define the igp (interior gateway protocol)?
1900 Value in which type of access list?
Explain the term 'unicast'.
i have donE B.E. IN COMPUTER SCIENCE AND THEN CCNA CERTIFICATOIN PLEASW LET ME KNOW IF ANY COMPANIES R HIRING FRESHERS PLEASE REPLY ON MY EMAIL ID karnailthakur@gmail.com
How do areas benefit a link state inter network?
1>What do you mean by Networks and Networking? 2>Difference between Vlan And Sub Interface Vlan? 3>What is Fiber Optic Media Converter? 4>What is Firewall? 5>Difference Between Layer2 and Layer3 Switch? 6>What is the function of Multilayer Switch? 7>Expalin STP? What is the Difference between STP and MST? 8>What is the Function of VTP?Explain the modes of VTP? 9>What kind of Message VTp will Send? 10>What is the Difference between Normal and Manageable Switch? 11>Difference between Local Vlan and End to End Vlan? 12>Difference between Distance Vector and Link State Routing protocol? 13>What do you mean by Backbone Fast Port? 14>what is Root Guard and BPDU Guard?
