How can we calculate quantity of slab, beam @ column ?
Beam should be calculated by deducting slab thickness or
slab should be calculate in to in ?
Answers were Sorted based on User's Feedback
Answer / sjtbehera
it is easy
length x breadth x height = qty.
if you calculate slab, if you adding beam thickness then
while you calculate beam you will deduct the qty. of beam
from qty. of slab
| Is This Answer Correct ? | 47 Yes | 10 No |
Answer / vivek
the beam thickness should not deduct the slab thick,
| Is This Answer Correct ? | 22 Yes | 9 No |
Answer / g.satyanarayana
Beam Qty = over All Depth of Beam x Length between Columns x
Width of Beam
Slab Qty = Length & Breadth to be considered from inner face
of Beam to inner face of beam and thickness of Slab
Column Qty = Over all height of Column including over all
beam Depth
Finally deduction of Steel Volume from the Total Qty So arrived.
| Is This Answer Correct ? | 16 Yes | 9 No |
Answer / gvb
just take all beams quantity, column quantity and slab quantity.(because slab thickness will be vary room to room like 41/2" to 5") so we have to calculate Beam, column and slab.
| Is This Answer Correct ? | 2 Yes | 2 No |
Answer / bharath m
Dear Mr.Jayesh,
Please Note:
1.Slab Concrete Quantity
Area of Slab including beam & Column covered area x Overall Depth of Slab.
2.Beam Concrete Quantity
Clear Span of BeamxBeam Widthx(Overall Depth of Beam-Overall depth of Slab)
3.Column Concrete Quantity
Lenght of ColumnxWidth of Columnx(Floor to Floor Height of Column-Overall Depth of Slab)
If still any queries pl. raise through Allinterview/to the Undersigned.
Thanks
Bharath
8438238335/9980644165
bharath.dce2006@gmail.com
| Is This Answer Correct ? | 4 Yes | 6 No |
How many kilograms of 12 mm coarse aggregate required in cufic feet for one cubic meter of M25 grade concrete
How to calculate cement required for m20,m5 grade
FOR concrete structure curing is important for hydration process,curing component is good for the concrete if W/C ratio is more than .38
i) Distinguish between Theodolite and dumpy Level? (Marks-8) ii)Distinguish between Viscous and Turbulent flow? (Marks-8) iii) Distinguish between nominal and design mix? iv) What is standard sand? v) Explain the term plane stress? Vi) Differentiate between principal plane and principal axis? Vii) write short notes on Elastic limit of structural steel? viii) Write short notes on stress concentration? ix) write short notes on "Grading of Sand" ? x) How many grades of concrete are there under standard concrete?
0 Answers Public Service Commission,
Whats the meanig of ,'K' VALUE in the case of soil.....
How can we improve the capacity of a existing foundation?
How many solid blocks can build one mason per 8 hours?
Steel calculation formala for column,beam and slab.
Cement require for 1sqm
what is superelevation?
What is the nature of duties & responsibilites senior civil engineer ?what is self confident & satisfaction should be a senior civil engineer?
how to caluclate sienerge qty in construction in ap
0 Answers Rites, VR Residency,
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)