Answer / ashok yadav acc cement

BIS has specied OPC in 3 different grades i.e. 33, 43 and
53 Grade depending upon the compressive strength of a
cement - sand mortar cube of 50 sqcm at 28 days.

However, PPC cement is having strength equal to 33 grade
OPC as per BIS.
As per BIS compressive strength at 3, 7 and 28 days are 16,
22 and 33 MPa (Min) resoectively.
But , Cement manufacturers are producing best quality PPC
having strength more than OPC of 43 Grade even 53 Grade in
some cases also.
BIS has not specified any Grade in PPC.

Finally concrete strength are depending upon the quality of
cement used i.e. mainly on 28 days compressive strength of
cement. It does not matter whether cement is OPC or PPC for
design - mixed concrete purposes. It purely depends on 28
days compressove strength of cement beside the other
factors i.e Water cement ratio, enviornment conditions i.e.
type of exposure, shape and size of aggregate, shape and
size of members etc,

Answer / raj

@mr.suresh if u dont know the answer please dont post wrong answers

Answer / mahendra mohan srivastava

There are no diffrence between OPC concrete and PPC
Concrete because Concrete is final product and you can make
what ever strength you have desire although using OPC or
PPC with the help of Design mix.

Answer / suresh

opc cement 43&53grade is there.
ppc cement only 33 grade only.
opc cement finnes very low.
ppc cement finnes very high.
SO strength easliy idfy in grade of cement.

Answer / mohammed aijaz hussain

Only difference is the rate of hydration that is the time to
attain the required strength will differ whereas the final
strength of concrete prepared by both types of cements will
be the same.

what is the procedure of steel?pleas tell me how we can apply in any home or building?

1 Answers  

---

manhole height is 1500 mm and width of brickwork is 230 mm dia of manhole covering is 560 mm brick masonry 1:4 horizontal length is 1500 mm and plaster 12 mm thick on both side 1:3. how to estimate the quantity of brickwork with mortar cement and sand for manhole chamber.

0 Answers  

---

how much steel required for 1 sq.m area?

12 Answers   L&T,

---

in 1:4,1:6 and 1:8 cement mortar mix how much water required? and find water cement ratio?

1 Answers  

---

what is the weight of 10mm,20mm,40mm aggregate

0 Answers   L&T, Ramky,

---

---

in the footings first which reinforcement bar has to be layed as per design criteria.

3 Answers  

---

1.WHERE THE SLAG CEMENT IS MAINLY USED. 2.FOR GOOD CONCRETE MIX OF M20 GRADE , CAN IT BE USED? 3. I WE USE FOR BRICKWORLiK AND PLASTERING ANY DISADVANTAGES?E

2 Answers  

---

how to calculate 1 cubic meter rcc concrete 1:1.5:3 ratio ,how much aggrates and sand , quanitites

3 Answers  

---

difference between tmt and tor steel

1 Answers   L&T,

---

How to calculate the crank length of the rod in beam? Please give me a details.

3 Answers   Agarwal Associates,

---

what is the quantity out-put by Hitachi-200 breaker for breaking or how to calculate

0 Answers  

---

1.DIFFERENCE BETWEEN NOMINAL MIX AND DESIGN MIX? 2.WHAT IS MEANT BY STRUCTURAL DESIGN? 3.IN STAAD WHY WE RELEASE MOMENT TO A MEMBER? 4.ON WHAT BASIS PARTIAL FACTOR OF SAFETY ARE DECIDE?FROM THE LOAD COMBINATION? 5.WHY WE PROVIDE EXTRA BAR & DEVELOPEMENT LENGTH AT TOP? 6.FULL FORM OF SPT & SMB? 7.WHAT IS MEANT BY ITP IN A CONSTRUCTION PROJECT? 8.WHAT IS LEAST COUNT OF THEODOLITE SURVEY? 9.WHAT ARE THE CAUSES OF FAILURE OF FOUNDATIONS AND REMEDIAL MEASURES? 10.WHAT ARE THE VALUES OF COMPRESSIVE STRENGTH? 11.STEEL CALCULATION FOR FOOTING,BEAM & SLAB? 12.WHAT IS MEANT BY GANTRY GIRDER? 13.IN SITE HOW WE CAN IDENTIFY THE ONE WAY, TWO WAY SLAB? 14.DIFFERENCE BETWEEN ANCHORAGE LENGTH & DEVELOPEMENT LENGTH? 15.BEARING CAPACITY OF STEEL SHUTTERING?LOAD CARRYING FOR SHUTTERING?

3 Answers  

---