In 3 phase induction motor 1hp current rating is 1.5 amps constant ? is correct

In 3 phase induction motor 1hp current rating is 1.5 amps
constant ? is correct or not ?

Question Posted / ramya

4 Answers
17041 Views
TATA, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

In 3 phase induction motor 1hp current rating is 1.5 amps constant ? is correct or not ?..

Answer / jatin

the current rating of an induction motor depends upon the load . so the value of current will change as per the load and not remain constant at 1.5 amps

Is This Answer Correct ?

23 Yes

6 No

In 3 phase induction motor 1hp current rating is 1.5 amps constant ? is correct or not ?..

Answer / narendra korrapati

motor amps is depends upon load.if load increase on motor
the full load amps will be change.practicaly i saw a 3-
phase 1 hp motor takes 3.5 amps

Is This Answer Correct ?

13 Yes

6 No

In 3 phase induction motor 1hp current rating is 1.5 amps constant ? is correct or not ?..

Answer / m bilal akram

a motor have manufacture at limited load if we put on extra
load may b motor winding brake at full load motor take
constant current if voltage and power factor also constant
however its Change current also Change.if load change
current also change.

Is This Answer Correct ?

4 Yes

0 No

In 3 phase induction motor 1hp current rating is 1.5 amps constant ? is correct or not ?..

Answer / pradyumna chandra panda

It is not justificable that current rating of 3ph motor is culculate to 1.5 amp per hp. Reactive power is more in higher size hp motor ie. slight less current per hp. And reactive power is less in lower size hp motor ie. more current per hp. Normaly 3ph 1hp motor take 1.8 amp per phase (phase current) Simiarily current rating of 3ph 5hp is 7.5 amp, 10hp is slight less then 15 amp and 100 hp motor is approximately 140 amp.

Is This Answer Correct ?

5 Yes

2 No

Post New Answer

More Electrical Engineering Interview Questions

what is meant by Ac & DC drives where its useful ? how its functioning ?

3 Answers

We use ungrounded DC system (220V/110V) for control and protection system in substations etc. Suppose we have long 2 core DC cables running from our DCDB in control room to the load (length of around 2 to 3 km). Do we need to protect these long DC cables from earth leakages or not? If yes how?

5 Answers Siemens,

Why is the diffrential protection in DG. What if the CT polarity is reversed while connecting for the same type of protection? How polarity can be made ok?

1 Answers

what are the specifications we must look at to select a relay for any capacity motor?

0 Answers

how digital four pin earth resistance tester works

2 Answers

Is a direct shorth ciruit on a branch MCCB in a Low Voltage Switchboard a correct means of tesing the performance for discrimination?

0 Answers Adani Power,

WHAT IS THE MEANING OF CYWY

1 Answers

We wish to test 60 Hz systems from a 50 Hz supply. To acheive frequency conversion, we use a VFD. The VFD powers 40 kVA transformer, which has motor and non-motor loads on it. Will the transformer work?

2 Answers Suzlon,

What are the causes ,revers rotation of a kwh meter?

2 Answers

why we use ac as a electric appliance in home or daily use?

1 Answers MNC,

-----------means a source which can supply a constant voltage to aload irrespective of the valu of load resistance.

2 Answers

What is meant by time harmonics and space harmonics?

0 Answers

For more Electrical Engineering Interview Questions Click Here