why ac can not be stored?

Answers were Sorted based on User's Feedback



why ac can not be stored?..

Answer / moorthi k

AC voltage have positive and negative voltage alternatively
sign wave form shape so positive and negative voltage are
equal to zero so cannot be stored

Is This Answer Correct ?    1 Yes 1 No

why ac can not be stored?..

Answer / rahul bisht

ac is a most higher current comperision by DC because DC is a constant current and ac is induction and fluxuation current and not a constant current and ac frequency 50hz and DC 0..than ac is not stor...may be.........

Is This Answer Correct ?    0 Yes 1 No

why ac can not be stored?..

Answer / ann

ac cannot be stored because it produced in bulk amount it is hard to stored ac ....

Is This Answer Correct ?    0 Yes 3 No

why ac can not be stored?..

Answer / harish thakur

because ac consist of positive and negative cycle.......but i was not confirmed

Is This Answer Correct ?    0 Yes 7 No

why ac can not be stored?..

Answer / k.prakashchandra

Because it is AC

Is This Answer Correct ?    2 Yes 13 No

Post New Answer

More Electrical Engineering Interview Questions

i have a roll dia aprox.43 inches and gear box ratio is 14.3.so my question is how was decide the kw rating of motor.

1 Answers  


what is resticted earth fault protection ? how did it protect & work in power transformer

3 Answers  


What are the different methodes for calculating the short circuit Current?

0 Answers   Equate,


HOW DO YOU CAN CHECK A 15KV DIODE, WHETHER IT IS OK OR NOT?

0 Answers   TMB,


WHY DOES NEUTRAL DO NOT CARRY EVEN THOUGH IT CARRIES RETURN CURRENT?

1 Answers  






What is meant by vector group

0 Answers   GPSC Gujarat Public Service Commission, VA Tech Wabag,


The rating of Transformer are 11KV, 22KV, 33KV instead of 10KV, 20KV & 30KV?

2 Answers  


We have two Al.busbars each of size 125mm*10 mm connected in parallel.To increase the current rating ,can we connect third busbar of size 100mm*10mm in parallel to existing two busbars?In my opinion ,if we connect busbars of different sizes in parallel,then the busbar of lowest size will take much current.So this type of paralleling should be avoided .Am I correct?

1 Answers   PDP Steel,


for distribution line ratio of x/r 1.<0.1 2.>10 3.>1 4.<0.01

3 Answers   HAL, HPPSC,


what is different between earthing and grounding for a electrical eqipment ?

2 Answers   BARC, Omega Maritime,


why the generator operating along with the infinte bus bar should never be under_excited?

1 Answers  


how we check vector group dyn7

1 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4452)
  • Electrical Engineering Interview Questions Electrical Engineering (16637)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)