Answer / abdul rehman

Transformer is a machine which transfer electrical energy
from high voltage to low voltage or low voltage to high
voltage as per consumer requirment ,but current transformer
is a instrument transformer which are used for measuring
and protective of electrical ckt. or equipment from many
kind of fault.

Answer / rms

the purpose of transformer is to convert the voltage at a
higher level or lower level depending on what purpose it
will be used. Step up transformers are seen at power plants
and substations so that it can transmit power at very long
distances. Step down transformers are seen attach at
electric post or even in electronic components..

A current transformer and potential transformers are very
important and only seen at thousand volts stations. Since u
cannot directly connect a kilowatt hour meter or other
relaying stuff at thousand volts because it will explode.
You need this ct's and pt's which will adjust the level of
the voltage at a certain ratio where it is now safe to
connect this meters and relaying stuff...

Answer / bs. nathan, iran

CT is a instrument which are used to supply a reduced valve
of current to meteres, protective relays & other
instruments.

CT ratio are express as a ratio of the rated primary
current to the rated secondary current.
eg: 300:5A here CT will produce 5A of Sy Cu, when 300 A
flows through Py.

Answer / sunil parmar

TRANSFORMER IS AN MACHINE USED FOR STEPPING UP AND DOWN OF
ELECTRICITY AND COMMONLY USED FOR EFFECTIVE TRANSMISSION
AND DISTRIBUTION PURPOSES.

AND CT GENERALLY KNOWN AS INSTRUMENT TRANSFORMER USED FOR
PROTECTION ,MEASUREMENT,AND FOR THE CONTROL PURPOSE.
IT ALSO PROVIDES ISOLATION BETWEEN THE HIGH VOLTAGE
TERMINAL AND METER TERMINAL.
DURING FAULT OR ABNORMAL CONDITION CT SENSES THE FAULT
CURRENT AND GIVES SIGNALS TO RELAY, AND RELAY TRIGGERS THE
CIRCUIT BREAKER.CT'S SECONDARY SIDE IS ALWAYS SHORT
CIRCUITED AND SEC. CURRENT RATING IS ALWAYS LESS ie.1,2,AND
5A

Answer / thrimurthy

transformer is an static device it power transfer to the
one circuit to another circuit without change the
frequency.and require of user if voltage step up or step
down etc.

Current transformer is an instument tranformer and used for
mesuring and protection agenst Earth fault and Over
current.

Answer / dileep t

Transformer is an electromagnetic induction device used to
change the voltage,current or power level in an electric
system.
Measureing of large current in power system is not possible
by the usage of normal measuring devices.
But current transformer (CT) is an instrument transformer
used to measure high current in power system.

Answer / venkatesan.j

1. A transformer in as electrical equipment for transfer of
power at required voltages. Whearas current transformer is
a primary sensing element for the measurment of current in
a circuit.
2.I a transformer the primary current is governed by the
loading or in turn the secondary current,but in case of
current transformer the secondary current is governed by
the primary current.
Current Transformer is a step up transformer.

Is there chopping current in resistive circuit

0 Answers  

how much percentage(%) of load can feed in power transformer?

1 Answers   Siemens,

How can we find out LT UG cable fault (size,from-4*25mm sqr to 4*300mm sqr)? How mani types UG cable faults?

0 Answers  

hi Is there any possibilities to find out the rotation of a shaft or something else by using electromagnectic waves or by IR rays.If s then can v change the dir., of rotation of the same by remotely?& how? plz dn't any1 say "NO r CAN'T"

0 Answers  

For which purpose the temp. rise test of transformer is conducted?

2 Answers  

what is the relationship between phase & neutral

0 Answers  

how to decide no of electrodes for 1600A LT Main incomer panel

0 Answers  

What is BUCKBOOST TRANSFORMER and Operation of Buckboost transformer?

4 Answers   Voltamp,

What is the reason of polyphase induction motor tripping suddenly on high current during running at 70% laod? Motor IR , winding resistance & inductance balance. Motor no load current is balance and ok as per mgfr. data.

0 Answers   GNFC,

what questions are asked in the interview for the post of an electrical maintenance engineer in FMCG companies?

0 Answers  

We have 800KW motor operating at 6600Volt,50 Hz supply.During 1st startup it tripped on overcurrent trip.It's FLA is 88 Amps.The K factor of Thermal overloaaad was set on .94 initially.then we set at 0.97 and then it started fine.i dont understand why it tripped first?What are the protections which comes in picture during starting ?

6 Answers  

hello friend i wish to study a course related to the electrical construction, controlling and monitoring , which course i want to study? pls give me the name of institute?

0 Answers