What are causes of cracks in outside plaster of a building
and how we prevent it during constructions?
- 6 Answers
- 11125 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / aung
crack can repair
to avoid causing these make sure curing,
wet the bricks before placing ,
bricks absorb water form plaster motor cause these crack also
| Is This Answer Correct ? | 15 Yes | 0 No |
Answer / aditya richie
being an exothermic reaction heat is released, for reaction
to continue properly curing is extremely nesessary . cracks
occur due to lack of or inadequate curing. curing for 28
days is necessary.
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / amy
Simple, the lime are either in powder form or during
mixture, the substance are not mixed well. Second reason
may due to loss of liquid during laying or substance left
idling too long. Upon laying to surface of brick walls. In
2 to 3 months time, hairline cracks tends to appear. to
repair these cracks, for external wall, please use ready
mix ASG to make good.
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / vengalarao
Mainly cracks form if mixing ratio is not properly done. Comonly we use 1:6 for 9" and 1:5 for 4" bricks. If mix with water and sand is not proper cracs we form
To prevent if crack observed remove the plaster and attach chicken mesh and plaster upon it
| Is This Answer Correct ? | 1 Yes | 1 No |
Answer / sjtbehera
There is very little that you can do, to prevent a plaster
ceiling from cracking. If it's going to crack, there is
nothing you can do to avoid this. However, these cracks can
easily be repaired using
Fiberglas drywall tape and finishing it with drywall joint
compound.
I have probably made this repair sound easier than it is,
but there is another alternative. You could fill the crack
with a good paintable caulking. Make sure that the caulking
you use is paintable, some silicone-based caulking aren't
paintable. If the caulking can be painted over, it will
save paintable on the tube of caulking.
| Is This Answer Correct ? | 3 Yes | 4 No |
If we don't have drawing for Excavation of building,At what rule we will go for excavation and how much depth will go for a villa?
how inovative you are?...how do u define innovation?
what happening if we casting HV shunt reactor foundation pad at 50cm height different time (One day difference)
how many pcs of steel bundule in all dia 8,10,12,16,25,32,40 please how many pcs in bundle of packing??
how much cost of single coat 20mm thick plastering per sqre meter
What is the l/d ratio of cantilever beam?
which grade of concrete is the strongest? M20,M25,M30,M35 or M40?
I am doing a engineering contract with GOI. I have purchased certain material from outside Maharashtra and paid CST on that material @ 5.25%. Please intimate whether I will be liable for VAT or VAT on works contract or not.
I want to calculate the footing 90º L bend as a techincaly
can i make bricks using M10 grade concrete ? and what would be the cost of a brick if we use m10 grade concrete sand and aggregates ??
what is difference between fluidity and workability also how palsticizer works
How much is anchor length ?
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
