Answer / k.s.yadav

Earth fault protection will be defunct.

Answer / privin p v

according to KCL midpoint of a star connection is zero potential.If the load of the transformer is balanced nothing happen while neutral earthing broken.But in case of any unbalancing occurs there is no way to go the circulating current and heat occurs.It will damage the transformer

Answer / tejpratap pandey

trnsformer phae to neutral voltage unbalanced & its may
dammage load side equipment.

Answer / r.ramadoss

Netural is providing in the transformer for passing 3rd
assymentrical current , if the netural was not present ,
due to the surge voltage or un balanced voltage the
transformer life time will be decreased

Answer / anand

harmonics will increase and sinusoidal output will tend to
become a bit nonsinusoidal

Answer / dk gnfc

When neutral open,line voltage flowing in phase,so overvolage occurs in all phases,and if REF provided,it will trip the transformer as protection against neutral opened from earth

Answer / latika

Question should be more specific.

Answer / nagaraju n

in this condition is un safe condition .

transfarmer is become fail to operation.& become a dameged

Answer / srinivas

there is a standby earthfault will occur on load side.

Answer / thuranga

Normally any power or normal transformers is designed in
such a way that all the three phases will be 99.9% balanced(
winding wise).
so neutral in transformer is not at all needed,but for extra
protection neutral is put.

so if the neutral is not present,there may not be any much
change in its operation but vibration of the transformer
might increase.only that will be the change.

what is the main difference between simplex RTD and Duplex RTD?

6 Answers  

What is the formula to calculate a three phase alternator

0 Answers  

How one can check the MAIN of a house wiring ?

0 Answers  

What is the Frequency while we step up the voltage from 220V to 11KV? Is it possible? Explain it?

2 Answers  

1. alternator has full load regulation of 4% when pf of the load is 0.8 lag, 1500 rpm. full load regulation of 1400 rpm for 0.8lag will be ________ ?? 2. torque angle of a sync m/c operating from a constt voltage bus is usually defined as space angle between _______ . 3. method most effective in finding out no load losses in large DC shunt motoris ______ . 4. current carrying capacity of fuse material depends on ______ . 5. coil has res. 10 ohm, inductance 1H. what wil be current after 0.1sec after switching on to a 500V DC SUPPL ? ? 6. effect of phase lag compensation on servo systems ___________ . 7. rotor of a dc machine is usually supported upon ______ . 8. DC motor is preferred to AC motor in which application ?? 9. 3 nos of 10:1 Xmer are connected in Star-Delta to supply a load at 230V.the supply voltage must be ______ . 10. voltage source produces max current in which circuit. 11. cal. power, if current and voltage are out of phase by 90 degree. 12. suitable length of Xmission line of power at 66 KV. 13. Which of the theorm helps in simple computation when the load across a ckt is varying ?? 14. what is the adopted line length for power Xmission of power by cables ??

5 Answers   TATA,

best manufacturer for busbar for outdoor switchyard having double bus bar scheme, can any one share technical specification of busbar. 132kv voltage ?

0 Answers  

How CFL &T5 tube light glows?

0 Answers   HAL,

1) name the communication cable and how it is communicate in between plc to modbus , plc with hmi? 2)name of the communication cables?

1 Answers  

What is the difference between alternator and generator?

0 Answers   IOCL,

7- What is the Dissipation Factor and the difference between it and Insulation Resistance Test? 8- What is the task (function) of DC and AC reactors in power plant? 9- What is the task (function) of (open delta with earthed) in some types in transformers? 10- What is the base of the selection of the vector group in transformers? 11- What is the zig-zag transformer and its function by drawing in large detail? 12- What is the polarity ? 13- Why we make short between phase(R) in high side and phase (r) in low side in vector group test? Where High Side ( R ,S and T ) and Low Side ( r ,s and t ). 14- What are the time on delay and time off delay? 15- What is the vector group? 15- What is the task (function) of different types of vector group such as Dyn11 , Dd0 , YNd1,……..,?

0 Answers  

Please explain me abt PQ diagaram in the power sector.

0 Answers  

How to calculate motor current for 3 ph & 1 Ph motor from KW rating?

3 Answers