Answer / manjunath

Hi,
P ls Check find the answer ......





It is the Greatest demand of load on the power station
during a given period. it sometimes also called as "system
peak" It is called maximum demand.



Sent By
manjunath And Rajshekar

Answer / elangovan t

It is the highest amount of power drawn (real/apparent)from
the grid by the plant during any 1/2hr duration in a billing
period.

Answer / rohit garg

For a power plant Maximum Demand is a important factor for
deciding its billing and the requirement of power from the
electricity board. It is defined as the peak demand of
power whenever the maximum load is there in operation or in
running process in the plant for the particular time period.
Maximum Demand is used to decide contract demand too and it
is generally kept at 75-80% of contract demand. If demand
of plant exceeds maximum demand limit at any time there
will be penalty for that.

Answer / ansar electrapower

it is the greatest demand attain .or it is the peak load
attaining during this period.
max.demand=connected load/diversity factor

Answer / azeem

maximum demand is the product of connected load and the diversity factor.

if a plant is having a motor assembly of 200 kw connected load
than the maximum demand will be(200 kw * 0.85 diversity factor)= 170 Kw for time interval

Answer / loboreliance2003

The greatest average value of the power, apparent power, or
current consumed by a customer of an electric power system,
the averages being taken over successive time periods,
usually 15 or 30 minutes in length.
The maximum demand of an electrical installation, so far as
tariff purposes are oncerned, is the maximum rate at thwich
the supply is being used during any complete half-hour
period, and is measured in kilovolt-amperes (kva). Kva is
similar in value to KW but is usually in the case of motive
power, 10-20% higher. For instance if a 20kw motor and a
6kw heater are on for a half hour period then the MD would
be in the order of 28KVA (assuming kva to be 10% higher
then KW on motor) The ratio of KW to KVA is called power
factor.

Answer / rizwan

It is the maximum number of installed appliances at the
consumer premises used at a particular time.

Answer / bala.a

This is the maximum power Continuously consumed by the
consumer.

Answer / heamkumar

Maximum Demand means if a plant is running with their
connected load (or) running load, at the month end the
total power consumed by the plant,(in KWH) is said to be
the Maximum Demand achieved.

WHAT IS LOAD CELL

0 Answers   AP, TATA,

what is the role and fuction of automatic transfer switch in rotary ups

0 Answers   Dynaspede,

WHERE IS THE LIGHTING ARRESTER SHOULD BE PLACED IN DISTRIBUTION LINES?

6 Answers   Bhel,

what questions will be asked for 11/33KV licence interview APSEB hyderabad. Can any one share question and answers.

0 Answers  

in railways why we use the power in 10,20 30kv,why not in the multiple of 11kv

2 Answers  

What is PIR (pre inserting resistance) in 400kv EHV SF6 BREAKER? Why it use?

1 Answers   Adani,

diesel generator not getting start so whats problems will happen to DG and how we can start DG

1 Answers   Lodha,

Who are the manufacturer for Nitrogen based Fire Protectio/explosion prevention for Oil Filled Transformers? India and international both?

0 Answers  

what is the diffrence between preventive maintinance corrective maintinance?

7 Answers   Siemens,

CAN ANYBODY PLEASE TELL ME HOW TO DESIGN A SERIES REACTOR FOR LIMITING SHORT CIRCUIT FAULT CURRENT??

0 Answers  

what is a composite error in current transformers, why occurs & in which it will occur i.e, either metering ct/ protection ct

0 Answers  

how to failure indution motor insulation & how to improve heat in motor insulation

0 Answers   BHL, EPIL, IFFCO, Micromax,