Answer / deepika tola

Because any line has an impedance, and acc to a simple law
known as ohm's law, voltage drop, V=IR.. so wen ther is
resistance/impedance, any line, whether it be 3-phase, 1-
phase, d.c. or any new invention...... it WILL have a
voltage drop!!

Answer / ram_svepl

BECAUSE TRANSMISSION LINE ITSELF HAS ITS OWN IMPEDANCE
(JUST LIKE A SERIES CONNECTED LOAD)

Answer / jnanesh

Voltage drop especially in 3 phase system is due to low
power factor.Low power factor leads to increase in I2r
losses which in turn increses the regulation.As regulation
increases voltage drop occurs which directly effects the
efficiency of generation and increase in stress of
transmission line.Thats why KEB people who are responsible
for maintaining required voltage put fine if we maintain
low power factor.Corona and skin effect are negligeble .

Answer / mbeki

due to resistance of the conductor,V=IR, corona effect for
high voltage lines.

Answer / ismail

due to corona and skin effect in transmission line.

Answer / alshaikh

Because, the transmission lines are inductive conductor they have impedance and they absorb reactive power. So, we add capacitors to give reactive power to the transmission lines then will not be any dropped voltage.
But, if the transmission lines are resistive, then adding capacitors will not solve the problem because the resistive lines do not absorb reactive power.

Answer / sanjay s.patil

one reason is due to overloading and due to faulty
equipments connected to the line.

Answer / rodel b. serad

Due to Overloading and also the cable used has owned
resistance that can consumed voltage

Answer / mohammed ayyub

due to unbalance in line

Answer / sumitgarg

skin efect and corona effect r the most common effect that
causes the line voltage drop.
apart from that drops the very major and very technical
effect that cause loss in poer and freq. is reactive poer
loss.
than can be compenseted only by using Capacitor Bank.

How should i design a 1ph & 3 ph transformer. Kindly let meknow all steps and formulaes related to design from scratch.

0 Answers  

Why current transformer is earthed??

2 Answers  

how does relay works?

16 Answers  

In all the generators, the excitation supply is DC. What is the significance of DC excitation? What will happen if AC supply is given as excitation supply?

2 Answers  

WHAT IS THE MEANING OG (li = 7 In)

0 Answers  

When measuring the Insulation resistance of a motor winding (winding to earth) using a megger meter, Applied voltage(1000V) was automatically reduced to 500V. and the measured insulation resistance values are also very low (in Kohm range) Can anyone give me a reason???

3 Answers  

can SMPS work in DC supply ?

10 Answers   HCL, IBM, Reliance,

This is about the recent problem that we have faced in our project site. We have 6/7.5 MVA. 66/11kV three phase star - star power transformer. The neutral was solidly connected to the earthing mat. But because of high resistance of earthing mat (130 ohm on LV and 180 ohm on HV), one day LV side neutral earthing conductor melted and we had a huge damage. Can any one plz tell me what might happen when we connect power transformer neutral to the earthing mat which has high resistance (>100 ohm ) ?????

2 Answers  

what are the values of VRY,VYB,VBR,Vry,Vyb,Vbr,Vrn,Vyn,Vbn for Magenetic balance test of 100 KVA and 63 KVA Distribution transformer

0 Answers  

What motor is used in ceiling fans and what motor is used in table fan.? why table fan is costlier than ceiling fan?

6 Answers   Bhel,

How to calculate total harmonic distortion level(THD) in VFD? and how can we reduce harmonics?

0 Answers   Apollo,

how much Hp motor is required for water suction pump in home uses ?

1 Answers