Answer / s s

BUS as name indicates is nothing but the carrier of current.

Answer / vinothbabu.k

BUS IS A TYPE OF CONDUCTOR,MADE OF ALLUMINIUM OR BY
COPPER,AND IT WAS INSULATED OVER IT. ITS USE TO CARRY
CURRENT.IT MAINLY USED IN THE PANEL BOARD,BUSDUCT,TRUNKED
SANDWITHED BUS BAR.MAINLY THE BUS BAR WILL NOT OPNED IT
WILL BE ENCLOSED ONE.

Answer / arpit kohli

BUS IS AN OPEN CONNECTED LOOP HAVING CONSTANT VOLTAGE &
FREQUENCY.

Answer / vinni

infinte bus is basically a constant voltage and constant frequency line....which offer an infinite impedance and act as non-rotating generator

Answer / om prakash vishwakarma

Bus is the way of current with the help of that a lot of
Load cable can be run and number of load cable is depend on
size of bus (squire inch).

Answer / niranajn

bus means in general refered as collection of electrical
energy

Answer / jagadish.s

BUS IS NODE IN SUBSTATION. IN LAYMAN'S LANGUAGE IT CONNECTS
THE INCOMING LINE TO A OUTGOING LINE/LOAD

Answer / anil bhatia

Bus or bus bar is midiator where one incomming and no of
outgoing or branches connected.

Answer / a manoj kumar

bus bar is the one which carries larger currents of 3000A< in a power plant

Answer / amit kr singh

busbaar is the very safe and lot of input output best thing
are safety is carrying current to load
features
compact size
safety no danger
use as high current carrying
used in mainly panel

can any one provide me a connection wiring diagram for a DG set control panel along with BOM?

0 Answers   Omaxe,

describe your self.

2 Answers   Amazon, Bechtel,

which type of ICs can be used in resonant power converter?

1 Answers  

raleigh method

0 Answers  

how do you calculate IKW(consumption per TR) in HVAC?

27 Answers   Aircon, CBRE, Cipla, Clivet, Cushman Wakefield, JLL, Sodexo, Voltas, Wipro,

I have a transformer 3phase 11kv/410v and its name plate missing. now how can I judge its rated kva?

2 Answers   Coca Cola,

what is the Auto Mains Failure Panel function in DG?state its function?

3 Answers  

what is electronic regulator and how we can use that in fans?

3 Answers  

1. A 380 / 220 V r.m.s. 3-phase 4-wire circuit carries loads of 8 + j8.1 ohm; 4 + j4.1 ohm; and 2 +j2.1 ohmin the three phases respectively. The length of the circuit is 100 m, and the resistivity of the phase conductors is 0.0005 Ω/m. The neutral conductor is of the same size as the phase conductors. a) Select a reference angle 0for the first phase. Then write down the three phase voltages in both polar format and complex number format. b) Make appropriate assumptions, and take temperature effects on resistance is insignificant. Calculate the currents in the three phases. (Note: Determine conductor resistance, and apply Kirchhoff’s Voltage Law) Based on the result, suggest a main switch rating for the circuit. c) Show your preferred direction of neutral current in a diagram, and then determine its value. (Note: Apply superposition principle, and Kirchhoff’s Current Law) Use its magnitude to show that in this circuit, the unbalanced load may increase the voltage drop in some of the phases. (Note: Also observe the common volt drip in neutral) State your assumptions, if there are any. d) Suddenly the neutral wire of the circuit is broken. Estimate the new currents in the first phase, i.e. Phase L1. State your assumptions, if there are any.

0 Answers  

What is meant by celling voltage & current in excitor ?

0 Answers  

Motor and transformer working with same principle so why motor rotates while transformer not?

7 Answers  

what is the difference between R Y B windings in three phase.does it differ by construction or by number of windings?Explain the difference between them.

3 Answers