Answer / srinivas b

Ovality is one of the geometrical parameter. If the
roudness is in the form of oval shape then it becomes
ovality.

Answer / karthick

ovality is defined as the deviation from the regular
circularity.assume the oval shape in resemblance to
elliptical shape and the percentage of ovality can be found
out by 2(a-b)/(a+b)
where
a----->length of major axis
b----->length of minor axis

Answer / anil kamat

supposely you consider the 2 axis x and y of a circular
object and radial distance along x is greater in one
dirction than other three directions then the condition is
called as ovality. This can be measured by rotating it on
simply supported bearings and the using a dial gauge.

Answer / govindraju.v

The difference between upper limit & lower limit is called
ovality

Answer / vinodparimal

the diameter size varition arround the periphery

Answer / siraj

Ovality is the deviation from circular shape.its diameter will not be uniform.

Ovality = (Max. outer dia-Min. outer dia)/Nominal outer dia

Answer / sudhakar jnapati

The distortion of the cross-section of pipe or tube from its normal (round) shape, usually expressed as a percentage of the difference between the major and minor axes of the starting material compared to the OD before bending.

Answer / murali

Ovality is the degree of deviation which os occured inside periphery of the circular object.

Answer / e.mohan kumar

if consider circular object(pipe) difference between maximum diameter of pipe to minimum diameter of pipe results is called ovality

Answer / iftehar hussain

With reference to the engine manf. tolerances and record sheet, using a calibrated micrometer. Bottom end bearing is removed from crankpin / piston removed. Surface wiped clean. Then at the specified points in the record sheet, measure the diameter. Normally at least 0, 45, 90, 135 deg. with ref to TDC and 5 equal distance locations across the pin.

Why cad cam is better field against IT field?Is the salary is good in this field and if it so then what is the average salary in this field because I don;t think that salary is good enough in this field.

0 Answers  

an ice block submurged in the water, if the ice melt level of water

40 Answers   NTPC,

sir i appeared to bosch written test recently and i cleared it successfully.can u suggest me how the interview will be done ?is it technical or HR or both?how shall i prepare for it?i am very eager to work with and in fact it is my dream job suggest me how to grab the job.if you know tell what type books are prefer for preparation of intrview?

0 Answers  

what is bearing journal?

4 Answers   CPCL, SCCL,

A Wheel accelerates from rest with an acceleration of 6 rad/sec seq. How many revolutions are experienced in 4 sec.? give answer with solution.

4 Answers   Essar,

difference between fasteners & sheet metal company

0 Answers  

i just wanted to ask that what should one do to clear all the concepts a mechanical engineer needs to have cleared,this not only includes the concepts of each and every semester of his engineering course, but also the basic laws and fundamentals of physics(that required for Mechanical engineering).I am a third year mechanical engineering student and i am very keen to know about the above question. somebody please help me.

1 Answers  

can any1 suggest me the books for placement papers.

1 Answers   Jindal,

hi, im rahul i working on project BUSINESS PROJECT REENGINEERING,IM DOING MY PRODUCTION ENGG & BPR IS MY FINAL YEAR PROJECTS, HOW CAN DO MY PROJECTS? I KNOW NX3,CATIA,PRO-E SOFTWARES (MODELING SOFTWARES)

0 Answers  

Why do you want do MS in Mechanical Engineering in US

0 Answers  

Is it ABS AH 36 material equivalent to IS 2062 Gr B material.

5 Answers   CPF, Mukand,

Name the four most important components of a Freon refrigeration system.

0 Answers   RRB,