POLYMER ENGINEERING - QUESTION 24.1 : The molecular weights M in kg / mol of 3 different monomers a, b and c in a polymer are Ma = 14, Mb = 16 and Mc = 18. The fraction of polymer chain X of 3 different monomers a, b and c in a polymer are Xa = 0.5, Xb = 0.3 and Xc = 0.2. (i) Calculate number average molecular weight by using the formula Ma Xa + Mb Xb + Mc Xc. (ii) Calculate weight average molecular weight by using the formula (Ma Xa Ma + Mb Xb Mb + Mc Xc Mc) / (Ma Xa + Mb Xb + Mc Xc). (iii) Calculate the polydispersity by using the answer in (ii) divided by answer in (i). (iv) If the molecular weight of repeat unit is 12, calculate the degree of polymerization by using the formula (Ma Xa + Mb Xb + Mc Xc) / (molecular weight of repeat unit).

1 Answers  

---

Why cavitation is produced

1 Answers  

---

Name some common problems associated with dilute phase pneumatic conveying?

0 Answers  

---

QUANTUM COMPUTING - EXAMPLE 32.10 : In quantum computing, the conversion of Control Not (CNOT) gate in two input quantum bit gate could be decribed as : | 00 > --> | 00 >, | 01 > --> | 01 >, | 10 > --> | 11 >, | 11 > --> | 10 >. If | P > = 0.707 ( | 01 > - | 11 > ), find the value of CNOT | P >.

1 Answers  

---

Question 52 - The half-life for first order reaction could be described in the differential equation dC / dt = -kC where k is a constant, C is concentration and t is time. (a) Find the equation of C as a function of t. (b) Find the half life for such reaction or the time required to reduce 50 % of the initial concentration, where k = 0.139 per minute. (c) When the initial concentration Co is 16 mol / cubic metre, how long does the reaction required to achieve the final concentration of 1 mol / cubic metre?

1 Answers  

---

---

how to reduce COD from plant waste water closed circulation system

1 Answers  

---

NATURAL GAS ENGINEERING - QUESTION 26.1 : (a) In natural gas pipe sizing, the length of the pipe from the gas source metre to the farthest appliances is 60 feet. The maximum capacities for typical metallic pipes of 60 feet in length are : 66 cubic feet per hour for pipe size of 0.5 inches; 138 cubic feet per hour for pipe size of 0.75 inches; 260 cubic feet per hour for pipe size of 1 inch. By using the longest run method : (i) Find the best pipe size needed for the capacity of 75 cubic feet per hour. (ii) Estimate the suitable range of capacities for the pipe size of 1 inch. (b) The maximum capacities for typical metallic pipes of 50 feet in length are : 73 cubic feet per hour for pipe size of 0.5 inches; 151 cubic feet per hour for pipe size of 0.75 inches; 285 cubic feet per hour for pipe size of 1 inch. By using the branch method find the best pipe size needed for the capacity of 75 cubic feet per hour when the length of the pipe from the gas source metre to the appliance is 52 feet.

2 Answers  

---

Why is respiration considered as an exothermic reaction? Explain?

0 Answers  

---

what is mass flow rate of steam of 7 kg/cm2 pressure in 1 inch id. pipe.

0 Answers   Ascent,

---

MASS TRANSFER - EXAMPLE 4.2 : In a non-dilute absorber, graphical method is used to represent the process. In an X - Y coordinate system, X-axis represents mole of carbon dioxide / mole of water and Y axis represents mole of carbon dioxide / mole of nitrogen. The inlet gas stream consists of 8 mol % of carbon dioxide in nitrogen. (a) Find the S / G minimum as a slope that goes through the point (0, 0.0304) and (0.0000488, 0.086957). (b) Find the actual slope of operating line when it is 1.5 times the S / G minimum! (c) Find the value of x for inlet gas stream when y = 1640 x, y is mole fraction of carbon dioxide in nitrogen.

1 Answers  

---

ELECTRICAL TECHNOLOGY - EXAMPLE 16.2 : In a selection of suitable heating equipment for drying of crystals of biochemical, the one of the lowest current consumption will be chosen for safety consideration. Selection is available : (A) 120 V microwave oven 1800 W. (B) 240 V conventional oven 11000 W. Which one should be chosen and why?

1 Answers  

---

AS PER IS(INDIAN STANDARD)RULES, IS INSTRUMENT EARTHING REQUIRE FOR INSRTUMENT WHICH IS ONLY 24V DC POWERED?

1 Answers  

---