Answer / kangchuentat

ELECTRICAL TECHNOLOGY - ANSWER 16.2 : For (A), AMPS = WATTS / VOLTS = 1800 / 120 = 15. For (B), AMPS = 11000 / 240 = 45.83. Dryer (A) should be chosen as less current is consumed. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.

Explain what are the problems that are associated with the expansion joints?

0 Answers  

---

Question 68 – Biochemical Oxygen Demand (BOD) could be calculated using the formula BOD = (DOi - DOf) (Vb / Vs) where Vb = Volume of bottle in ml, Vs = Volume of sample in ml, DOi = Initial dissolved oxygen in mg / L, DOf = Final dissolved oxygen in mg / L. (a) By using a bottle of Vb = 300 ml with sample Vs = 30 ml, find the BOD if DOi = 8.8 mg / L and DOf = 5.9 mg / L. (b) By using a bottle Vb = 600 mL with sample Vs = 100 mL, find the BOD if DOi = 8.8 mg / L and DOf = 4.2 mg / L. (c) Find the average BOD = [ Answer of (a) Answer of (b) ] / 2. (d) If the BOD-5 test for (a) - (c) is run on a secondary effluent using a nitrification inhibitor, find the nitrogenous BOD (NBOD) = TBOD - CBOD. Let TBOD = 45 mg / L and CBOD = Answer of (c).

1 Answers  

---

THERMODYNAMIC - EXAMPLE 10.1 : The water is superheated steam at 440 degree Celsius and 17.32 megapascals. Estimate the enthalpy of the steam above. From the steam table for water at 440 degree Celsius, enthalpy of steam, h at 18 megapascals is 3103.7 kilojoules per kilogram and at 16 megapascal is 3062.8 kilojoules per kilogram. Assume that h = mP + c where P is pressure; m and c are constants at fixed temperature with small differences in P.

1 Answers  

---

What is the pattern of interview questions and which field is of high importance viz., Mass Transfer, Heat Transfer, Petroleum Refining etc ?

2 Answers   Cairn, IOCL, Reliance,

---

Why is a vacuum breaker used on shell and tube heat exchangers that are utilizing steam as the heating utility?

0 Answers  

---

how to calculate overall heat transfer coefficient in insulated pipeline? Please give a answer with formula

2 Answers   NPCIL,

---

Chemical Engineering Unit Operation - Which of the sequence below represent a feasible flows of ethanol processing plants using cellulose as starting material? A. raw material --> heat exchanger --> distillation column --> reactor. B. reactor --> distillation column --> raw material --> heat exchanger. C. heat exchanger --> raw material --> distillation column --> reactor. D. raw material --> heat exchanger --> reactor --> distillation column. E. distillation column --> raw material --> reactor --> heat exchanger.

1 Answers  

---

why rotameter has variable area?? is it necessary??

1 Answers  

---

how can i prepare for gate chemical in kolkata

0 Answers  

---

What is the use of gear pumps in motor?

0 Answers  

---

Question 69 - A well delivers 225 US-gallons per minute of water to a chemical plant during normal system operation. (a) Calculate its flowrate in the unit of mega US-gallon per day or MGD. (b) The following formula is written next to the chlorine feed point : (chlorine feed rate, lb / day) = (flowrate, MGD) X (dose, mg / L) x (8.34). If this formula is correct, then what should the chlorine feed rate to be in pounds per day (lb / day) if the desired dose is 2 mg / L. (c) Prove by calculations that the constant 8.34 in the formula next to the chlorine feed point is correct. Let 1 US-gallon = 3.78541 L and 1 mg = 0.0000022046 pound.

1 Answers  

---

What are the some common problems associated with dilute phase pneumatic conveying?

0 Answers  

---