Which of the following are valid WAN terms? A.) DTE B.) DCE C.) Demarc D.) CPE

3 Answers   IBM,

---

What’s the default CDP holdtime in seconds for Cisco routers?

2 Answers  

---

Which feature should a routing protocol have to support vlsm?

0 Answers  

---

hi friends i donot know this is the networking question or not but if you help me then i will thankfull to you the problem is like that in my comnay there are 200 user which log one at a time now only one user is not able to get the dhcp address and othr are geting the dhcp my company sys admin is saying that this is the n/w fault while i am saying that this is not the n/w fault for the cleaerfication of my side i take a straight workng cable and connect that user directly to my cisco 24port switch now problem is stiil like that but one thing i wan to say he is geting manually ip and able to access internet he is able to ping the server but whrnever he tyeme \\<ip address of server> error comes like networl path provided not accepted by provider some thing like that. my systm admin is saying that i have o do somthing on my firewall but i am saying that no issue with firewall in that i connect my latop to the spefic port from where the user is conected then i am geting dhcp ip address and i am able to connect the server also i donot know why this is happen my syadmin is senior to me so i canot blame him plz help e what to do i am very weak in the filed of systym jitendera kumar sinha

6 Answers  

---

Which command, that is used to test address configuration, uses Time-To-Live (TTL) values to generate messages from each router. A. trace B. ping C. telnet D. bootp

1 Answers  

---

Which memory component on a Cisco router contains the dynamic system configuration? ROM NVRAM Flash RAM/DRAM

17 Answers   HCL, Sun TV,

---

In regards to the OSI seven-layer model, at which layer is EBCDIC and ASCII? A.) Presentation B.) Application C.) Transport D.) Session E.) Datalink F.) Network

1 Answers  

---

What are the three sources of signal degradation on a data link?

0 Answers  

---

I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

5 Answers  

---

Choose the following that are benefits to segmenting with router: A.) Flow Control B.) Manageability C.) Multiple Active Paths D.) Explicit packet lifetime control

1 Answers  

---

A big part of the overhead on a network is broadcasts. You divide a large number of hosts into smaller individual networks and separate them with the proper device According to proper networking terminology you have created separate _______________________, User Domains Broadcast Domains Collision Areas Broadcast Areas

1 Answers  

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

4 Answers  

---