Which memory component on a Cisco router contains the
dynamic system configuration?
ROM
NVRAM
Flash
RAM/DRAM
- 17 Answers
- 38384 Views
- HCL, Sun TV, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / rocket rajesh
RAM because it is a temporary memory. our data pass
through ram before processed by processor.
| Is This Answer Correct ? | 9 Yes | 1 No |
Answer / ashwani chaddha
ram, because it is a temporary memory. our data pass
through ram before processed by processor and we can save
it in nvram that is non-volatile random access memory. It
is permanent memory.
| Is This Answer Correct ? | 11 Yes | 4 No |
Answer / karma
RAM, because question is asking about dynamic system
configuration so it need change frequently. ROM, NVRAMand
flash memory are stable and we only change occasionally in
these memory, so what is left now is RAM, in RAM we
| Is This Answer Correct ? | 7 Yes | 2 No |
Answer / sunil arya
Ram, because it is a temporary memory. our data pass
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / amar
RAM is the right answer...
ROM,FLASH,NV RAM for static memory .. which wont be changed
frequently
| Is This Answer Correct ? | 3 Yes | 0 No |
Answer / ajay patel
RAM
Because all dynamic configuration save in ran then after
save in nvram
| Is This Answer Correct ? | 3 Yes | 2 No |
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
How Bridge Protocol Data Unit detect looping in Network? How Bridge Protocol Data Unit work? explain?
CSMA/CD stand for which of the following? A.) Carrier Sense, Multiple Access with Collision Detection B.) Collision Sense, Multiple Access with Collision Detection C.) Collision Sense, Multiple Access with Carrier Detection D.) Carrier Sense, MAC address with Collision Detection
Explain what is the size of hello packets in eigrep protocol?
Which OSI layer defines end to end communication, segmentation and re-assembly? A.) Network B.) Transport C.) Physical D.) Application E.) Data-Link F.) Presentation
How many valid ip will b in /21 in route summarization?
what is Bandwidth capping
Why ESP Transport mode is not compatible with NAT????? Though New IP Header in Tunnel mode & Original IP Header in Transport mode are out of Authentication & Encryption.
What is the function of Layer 2 Device?
What is the maximum hop count for Link-State protocols? A.) 15 B.) there is no hop count limit C.) 256 D.) 16
Which information must a router know in order to perform proper and pungent routing? A. destination application of an incoming packet B. number of other packets in a single flow of data C. destination network address of an incoming packet D. number of routers that also know a path to the destination
- What is EGIRP and IGRP - How EGIRP and IGRP works
CCNA 
