Answer / kang chuen tat

D. raw material --> heat exchanger --> reactor --> distillation column. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.

how to calculate material balnce & energy balnce

7 Answers   MahaGenco, Oil India, ONGC,

---

QUANTUM COMPUTING - EXAMPLE 32.4 : A system of linear congruences consists of 3 equations : X ≡ 1 (mod 2), X ≡ 3 (mod 3), X ≡ 4 (mod 5). X has positive values. (a)(i) List the values of these equations from 1 to approximately 40. (ii) Find the first smallest value and second smallest value of X. (iii) Guess the third smallest value of X. (b) Let X ≡ Aa (mod Ma), X ≡ Ab (mod Mb), X ≡ Ac (mod Mc). According to Chinese remainder theorem, X ≡ (Aa x Ya x Md + Ab x Yb x Me + Ac x Yc x Mf) [ mod (Ma x Mb x Mc) ]. (i) Show that Ma, Mb and Mc have the greatest common divisor of Ma x Mb x Mc. (ii) Find the values of Md, Me and Mf if Md = Mb x Mc, Me = Ma x Mc and Mf = Ma x Mb. (iii) Find the values of Ya, Yb and Yc if Ya = Remainder of (Md / Ma), Yb = Remainder of (Me / Mb) and Yc = Remainder of (Mf / Mc). (iv) Use Chinese remainder theorem to find X.

1 Answers  

---

Question 68 – Biochemical Oxygen Demand (BOD) could be calculated using the formula BOD = (DOi - DOf) (Vb / Vs) where Vb = Volume of bottle in ml, Vs = Volume of sample in ml, DOi = Initial dissolved oxygen in mg / L, DOf = Final dissolved oxygen in mg / L. (a) By using a bottle of Vb = 300 ml with sample Vs = 30 ml, find the BOD if DOi = 8.8 mg / L and DOf = 5.9 mg / L. (b) By using a bottle Vb = 600 mL with sample Vs = 100 mL, find the BOD if DOi = 8.8 mg / L and DOf = 4.2 mg / L. (c) Find the average BOD = [ Answer of (a) Answer of (b) ] / 2. (d) If the BOD-5 test for (a) - (c) is run on a secondary effluent using a nitrification inhibitor, find the nitrogenous BOD (NBOD) = TBOD - CBOD. Let TBOD = 45 mg / L and CBOD = Answer of (c).

1 Answers  

---

What is condensate lift?

0 Answers  

---

What is the main difference between deflection and null type instruments?

1 Answers  

---

How are plate heat exchangers used in an ammonia refrigeration system?

1 Answers   HJ, Reliance,

---

PROCESS DESIGN - EXAMPLE 21.3 : According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

1 Answers  

---

THERMODYNAMIC - EXAMPLE 10.2 : A cylinder with a movable piston contains 0.1 mole of a monoatomic ideal gas. The piston moves through state a, b and c. The heat Q, changes from state c to a is + 685 J. The work W, changes from state c to a is - 120 J. The work, W performed from state a to b then to c is 75 J. By using the first law of thermodynamic, U = Q + W where U is the internal energy : (a) Determine the change in internal energy between states a and c. (b) Is heat added or removed from the gas when the gas is taken along the path abc? (c) Calculate the heat added or removed when the gas is taken along the path abc?

1 Answers  

---

PETROLEUM ENGINEERING - QUESTION 25.3 : Liquid octane has a density of 703 kilograms per cubic metre and molar mass of 114.23 grams per mole. Its specific heat capacity is 255.68 J / (mol K). (a) Find the energy in J needed to increase the temperature of 1 cubic metre of octane for 1 Kelvin. (b) At 20 degree Celsius, the solubility of liquid octane in water is 0.007 mg / L as stated in a handbook. For a mixture of 1 L of liquid octane and 1 L of water, prove by calculations that liquid octane is almost insoluble in water.

1 Answers  

---

Question 66 – The drag coefficient Cd = 0.05 and lift coefficient Cl = 0.4 for a levelled flow aircraft are measured. The velocity of the aircraft is v = 150 ft / s with its weight W = 2677.5 pound-force. (a) Find the value of the lift of the aircraft, L, when it is also its weight. (b) The drag of the aircraft, D = Cd M, L = Cl M. Find the value of D. (c) The power required is P = Dv. If 1 pound-force x (ft / s) = 1.356 W, find the value of P in the unit of Watt or W.

1 Answers  

---

what are lubricants using in compression.

1 Answers  

---

What are the types of clarifier used in water treatement plant?

1 Answers   Adani,

---