What are the different protection systems takes place on control panel board?

Categories >> Engineering >> Electrical Engineering
Suggest New Category

What are the different protection systems takes place on
control panel board?

Question Posted / ravi

7 Answers
38358 Views
BSNL, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What are the different protection systems takes place on control panel board?..

Answer / vengatesh

1.Circuit Breaker
2.Protection relays
3.Fuse(over current protection)
4.Earthing(For drawn the Fault current which is higher than normal voltage)
5.Control panel body earthing(To prevent the body shorts)

Is This Answer Correct ?

20 Yes

1 No

What are the different protection systems takes place on control panel board?..

Answer / rajendran.m

Earthing system.

Is This Answer Correct ?

9 Yes

1 No

What are the different protection systems takes place on control panel board?..

Answer / rcq

1. Reverse power relay
2. Reverse kvar relay
3. Overcurrent and eatht fault relay
4. Trip/Lockout relay
5. Differential protection relay

Is This Answer Correct ?

5 Yes

1 No

What are the different protection systems takes place on control panel board?..

Answer / khajamian

MCB,s MCCB,S .....miniature circuit breaker and mould case
circuit breaker....and various relays..... [protective
relay,current relay, thermal relay..over load relay.. ]etc

Is This Answer Correct ?

5 Yes

2 No

What are the different protection systems takes place on control panel board?..

Answer / powerplantguruji

Interlocks:
Are the programmed or hardwired control systems to protect systems and improve the operation reliability.

Protections:
Are the programmed or hardwired control systems to protect the equipments, man power and systems from failure/harm.
To read more click here...
https://www.powerplantguruji.in/2020/11/interlock-permissive-protection-thermal-power-plant.html

Is This Answer Correct ?

0 Yes

0 No

What are the different protection systems takes place on control panel board?..

Answer / sridhar

(i) SPD(Surge Protection Devives)
(ii) Prevent the Oxiditation by painting
(iii)To choose the Proper Enclosure system

Is This Answer Correct ?

2 Yes

3 No

What are the different protection systems takes place on control panel board?..

Answer / sb

CT,PT & CB

Is This Answer Correct ?

0 Yes

2 No

Post New Answer

More Electrical Engineering Interview Questions

If 110V DC Coil Contactor taken 15ma DC on load,than how much AC current wil be taken?

0 Answers Lafarge, Shree Cement,

1. Design a counter which counts 0, 4, 8, 2, 6, and repeats using: 1.a using JK flip flops 1.b using T flip flops 1.c using D flip flops

0 Answers

plzzzzzzzzz plzz send me the papers of JSPL WRITTEN TEST..SO that i can prepare for the test in electrical engg..

0 Answers

how a synchronous motor is used as a resistor,capacitor and an inductor?

3 Answers Technocon Services,

why transformer are rated in kva.

5 Answers Dalkia, Nalco,

What is the actual formula for transformer short circuit test? below i given rating of the transformer.. 1000KVA, pri 11KV, Pri amp 56A. %Z 5.95..

2 Answers

where is core-type and shell-type construction suitable for transformers ?

0 Answers

what r the tests on the 3 phase transformers can any one explain how to test using megger on transformers thx

2 Answers

What is VCB? Where it is installed?

11 Answers Hyundai,

Explain the laying procedure and laying depth of submarine cables under sea?

1 Answers Schneider,

what is the dedicated neutral earth in ups? y its required?

4 Answers

What happens to the terminal voltage of an alternator connected to a bus bar when it is suddenly disconnected from the bus bar??

2 Answers

For more Electrical Engineering Interview Questions Click Here