when the motor was star position that is running ok but when the motor was delt

Categories >> Engineering >> Electrical Engineering
Suggest New Category

when the motor was star position that is running ok but when
the motor was delta it was tripped? why?

Question Posted / guest

5 Answers
5221 Views
Nimbus, SEL Manufacturing, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

when the motor was star position that is running ok but when the motor was delta it was tripped? wh..

Answer / pawanchauhan12

basically this type of problem created when motor winding delta coil sequence not proper. For finding of fault following this processor :- Firstly check motor winding continuity 1:5{RR} ,2:6{YY} & 4:3{BB} .if continuity not matched then interchanged sequence of {RR} wire of power .if problem not solved then again interchanged second sequence of {YY} wire of cable .

Is This Answer Correct ?

5 Yes

2 No

when the motor was star position that is running ok but when the motor was delta it was tripped? wh..

Answer / pramit dutta

By connecting the stator winding 1st in star and then in delta
,the line current drawn by motor at starting is reduced to 1/3 th as compared to starting current with the windings connected in delta.

Is This Answer Correct ?

3 Yes

1 No

when the motor was star position that is running ok but when the motor was delta it was tripped? wh..

Answer / santosh kumar kishore

in delta connection motor takes more current and in star
position motor takes less current so either change
connection or increase relay setting.

Is This Answer Correct ?

2 Yes

2 No

when the motor was star position that is running ok but when the motor was delta it was tripped? wh..

Answer / a p patil

motor star connection join winding terminal C2,A2

Is This Answer Correct ?

0 Yes

0 No

when the motor was star position that is running ok but when the motor was delta it was tripped? wh..

Answer / naveen joshi

There are many reason whether resistance increased by terminal contact in motor or phase difference in roter and stator not matched during transition from star to delta , increase the pause timing in timer .
.

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

What kind of preventive maintenance are there for transformer?

0 Answers Gulf,

What is the difference between reciprocating & rotary motors in AC units, which is the best one in terms of operation.

2 Answers MacLellan,

how many hvdc lines in india???

0 Answers

How to do stting of vl250 siemens MCCB

0 Answers Qatar Steel,

In a three phase transformer(delta/star connected)when i touch one end of the bulb in any one phase and other end to earth..will the bulb glow or not..if not why?..i'm touching the bulb in star connected side...

6 Answers

how much LT load can bear by the 100 KW HT connection.

0 Answers

in battery charging room we find two fuses (one in positive other in negative cables ).why it is so?one fuse is ore than sufficient?

0 Answers

How to convert farad to kvar. both are the unit of capacitor.

5 Answers College School Exams Tests, UltraTech, Vikram Ispat Industries,

Can any answer me ,What will be the range of C.T coil for L&T energy meter EM301 used for 180 kva DG set

0 Answers

we can run 2phase as 3phase .what will be the differnce with respect to phase angle, power, current between the two modes

0 Answers

what is the grounding Calculation formula? spouse i want to provide grounding to 3phase 18kw motor or i want to provide ground to 3phase 10kva dry type transformere or you give me any exemple...... Thanks.

0 Answers

What is the difference between INVERTER and UPS?

7 Answers

For more Electrical Engineering Interview Questions Click Here