T.x range -0.1 to 0.2 milibar,so how much mili ampear at 0.1 milibar?

Categories >> Engineering >> Instrumentation
Suggest New Category

Question Posted / narendradx

7 Answers
7543 Views
Sugar Factory, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

T.x range -0.1 to 0.2 milibar,so how much mili ampear at 0.1 milibar?..

Answer / karthikeyan kvp

TX range is -0.1mbar to 0.2mbar

span= maximum-minimum
= 0.2-(-0.1)
= 0.3

mA = given value- zero value/ span x 16+4

= 0.1-(-0.1)/0.3 x 16+4

= 0.2/0.3 x 16+4

= 14.66 mA

Is This Answer Correct ?

8 Yes

2 No

T.x range -0.1 to 0.2 milibar,so how much mili ampear at 0.1 milibar?..

Answer / sampath

LRV = -0.1 mbar
URV = 0.2 mbar
SPAN= 0.3 mbar

( 0.2/0.3 )* 16 + 4 = 14.67 mA @ 0.1 mbar

Is This Answer Correct ?

11 Yes

9 No

T.x range -0.1 to 0.2 milibar,so how much mili ampear at 0.1 milibar?..

Answer / dibyendu das

tx range= -0.1 to 0.2millibar
span =0.3

-0.1 = 4 mmA
-0.075 = 8 mmA
+0.05 = 12 mmA
+0.075 = 16 mmA
+0.2 = 20 mmA

this is the ratio to calculate 0.1 milibar = how much amps.

Is This Answer Correct ?

3 Yes

1 No

T.x range -0.1 to 0.2 milibar,so how much mili ampear at 0.1 milibar?..

Answer / manish

12MA AT 0.1AMP

Is This Answer Correct ?

2 Yes

4 No

T.x range -0.1 to 0.2 milibar,so how much mili ampear at 0.1 milibar?..

Answer / raju

9.33mA

Is This Answer Correct ?

0 Yes

4 No

T.x range -0.1 to 0.2 milibar,so how much mili ampear at 0.1 milibar?..

Answer / mohan

14.32

Is This Answer Correct ?

1 Yes

7 No

T.x range -0.1 to 0.2 milibar,so how much mili ampear at 0.1 milibar?..

Answer / sarath kumar

tx range= -0.1 to 0.2millibar
span =0.3
hence, mA at 0.1 miilli bar = 9.28 mA

Is This Answer Correct ?

4 Yes

13 No

Post New Answer

More Instrumentation Interview Questions

how far the two wire transmission (loop power) maximum distance suitable?

2 Answers PCIL,

how many types of orifice plates?and explain about it?

2 Answers Kesoram,

what is PM/CM/RCM?

2 Answers Emco,

Why 4-20 amps is being used in instruments? Why cant we use any other range instead of 4-20 amps? Why only 4 amps is taken as lower limit and why 20 amps is taken as the higher limit?

0 Answers

if a tank is contaning oil and water than how can we measure the oil and water level seperately

3 Answers

what is the function of a diaphragm?

1 Answers

What care will you take in the installation of control valves,SCADA,DCS and FOC in Oil and Gas Project?

0 Answers KNPC,

If boiler drum level transmitter is not working properly what you will do for resolving the problem in plant running condition?

2 Answers

What is DCS and PLC scanning time?

5 Answers

how to callibrate a new i/p converter

7 Answers TATA,

what is a vortex flow meter,mass flow meter and electromagnetic flow meter.particular use of this.means in which condition particular meter is used.

0 Answers L&T,

what is difference between wheatstone bridge, pirani gauge and strain gauge ??? explain its principle and working

4 Answers

For more Instrumentation Interview Questions Click Here