Answer / rajkumar

Few things have to be taken on Account

1, The process fluid, Say if its Sulphuric Acid mean you have
to consider the metalargy for pressure gauges,
2, Type of PG, say when you gonna Install on a Pump Discharge
head mean there will be more Vibration, so you have to go
for Diaphragm type of PGs, else Fill Fluid,
3, Normally we choose the Range of PG by multiplying the
operating pressure with 1.5, Say operating pressure 5
Kg/Cm2 means the PG range must be 0 to 7.5 Kg/cm2.
4, Depends upon the Pressure range, PGs also Differ.

Answer / sanjaydoshi

1. select proper range of pg
2. process tapping
3. service(pressure condition on process)

Why we use 4 - 20 ma?

6 Answers   IJT, ONGC,

---

tell about various protocols used in different plcs

3 Answers   Emerson, Samtel,

---

when the force applied on load cell the ohms will be varriying .and how its convert ohms to mv generate and have any formulae?

1 Answers   UETCL Uganda Electricity Transmission Company Limited,

---

Why grounding is necessary? Give example with diagram.

0 Answers   Bright Point, DS Group,

---

Why we use 250 ohm resister in series hart communicator?

3 Answers   Thermax,

---

why we are using boosters at glass furnace is there any other thing?

1 Answers   CGL,

---

please explain clearly in PID controller if We increase P only what will be action of the contrlere.

1 Answers   IMECO,

---

What is Difference between PLC and CNC ?

2 Answers  

---

why use MMWC unit

9 Answers   Praxair, Saipem,

---

Q- Control problem are mainly classified in _____ types. a-)4 b-)3 c-)6 d-)nono of these Few of them i know is 1- regulator type problem (eg- Air conditioner) 2- tracking problem (eg missile trcking problem) 3- sybernatics 4- optimal control problem

0 Answers   Sail,

---

1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling

0 Answers   BARC,

---

What is instrumentation amplifier?

3 Answers  

---