What are the types of TESTS in CIRCUIT BREAKERS based on
Testing and commissioning?

Answers were Sorted based on User's Feedback



What are the types of TESTS in CIRCUIT BREAKERS based on Testing and commissioning?..

Answer / yusuf

> Opening and Closing Coil Resistance measurement
> Contact Resistance Measurement. (This Ensures minimum
Voltage drop)
> Timing Test(Ensures Fault clearance time)
> IR Measurement(Ensure proper Isolation from Ground and
between Phases)
Other than these, H.V, Flash Test, Tan Delta are also done
in the factory

Is This Answer Correct ?    4 Yes 0 No

What are the types of TESTS in CIRCUIT BREAKERS based on Testing and commissioning?..

Answer / manisand1

Above all some more test is to included i will clear this
in next time.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

What is difference between Sample test and Routine test in safety standard?

0 Answers   Chicony Electronics,


why motor run slow speed in star connection?explain how?

3 Answers  


how many percent setting of motor over load relay of its full load current

6 Answers  


What is meant by power factor correction?

5 Answers   Aspire,


I need tnpsc AE Electrical question papers

2 Answers   TNPSC Tamil Nadu Public Service Commission,






What are effect of radio system in DCS Distributed control system ?

1 Answers   Sabic,


Why Dyn11 Transformer is selected for distribution transformer?

3 Answers   JK Associates, MSETCL Maharashtra State Electricity Transmission Co Ltd,


54 Comments Alok and Bhanu play the following min-max game. Given the expression N = 38 + X*(Y – Z) where X, Y and Z are variables representing single digits (0 to 9), Alok would like to maximize N while Bhanu would like to minimize it. Towards this end, Alok chooses a single digit number and Bhanu substitutes this for a variable of her choice (X, Y or Z). Alok then chooses the next value and Bhanu, the variable to substitute the value. Finally Alok proposes the value for the remaining variable. Assuming both play to their optimal strategies, the value of N at the end of the game would be?

0 Answers   Bajaj, TCS,


How does a digital electronic meter work??????

0 Answers  


A 25MVA 3300/400V T/F is termed as per winding is …… a) primary 3300V & Secondary 400V b) primary 3300V & low voltage winding 400V c) High voltage winding 3300V & Secondary 400V d) High voltage winding 3300V & low voltage winding 400V

4 Answers   Engineers India Limited,


what is the use nuetral wire

8 Answers  


Hi! iam Rajanikanth.Can u tell me FAQ's of AP TRANSCO.

1 Answers   APTransco,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)