my question is that....few days ago i had installed a three phase motor starte

my question is that....few days ago i had installed a three
phase motor starter for an electric saw.the motor will run
and make the hydraulic pressure which will be goes to
pressure cylender by up and down lever.two number of
limitswitches are also installed on cylinder for safety of
motor.now when the arm of cylinder reaches to the upper or
lower limit it will cut the motor's line.and motor will be
stop.now wana know that what will i do that motor runs
continue after the limitswitch cut it down but it shold not
be made any pressure.pls answer me in brief.

Question Posted / malikmazhar

3 Answers
3487 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

my question is that....few days ago i had installed a three phase motor starter for an electric sa..

Answer / pillay

The motor is driving a hydraulic pump.Install a relief valve
set at the correct pressure in your hyd system where the pump
can perform its task but when the piston reaches the top the
pressure build up will be too high and the excess pressure is
released through the valve, the limit switches wont be
necessary any more.the pump will be running all the time.

Is This Answer Correct ?

0 Yes

0 No

my question is that....few days ago i had installed a three phase motor starter for an electric sa..

Answer / malik mazhar

c0ntr0l its up and d0wn s0len0id valve thr0ugh limit switc..

Is This Answer Correct ?

0 Yes

0 No

my question is that....few days ago i had installed a three phase motor starter for an electric sa..

Answer / pvl

There should be some way to vent the excess pressure built by the motor. So first of all you should have a pressure gauge or sensor to read the pressure. Then you should have either a re-circulation line in the system or vent valve to channel the excessive pressure. When the hydraulic pressure reaches a set limit the re-circulation valve should open and channel the excessive pressure back to the tank/reservoir. In this way you can keep the motor constantly on without causing damage to system.

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

Can we use HRC fuse inplace of semi conductor fuse ? What are difference between them?

3 Answers

I've descovered that when the earth wire in a domestic electrical installation is not connected back to the board (ground) a voltage of between 9-24v is is found to be present in the earth wire. When connected at the board there is no voltage - is this normal and why does it happen?

3 Answers

why the the electrical machine coil are damage ? How to prevent it?

2 Answers

Difference between control junction box (cjb) and power junction box(pjb)?

0 Answers

what are the different types and applications of compressors?

1 Answers

why we are using KVA rating for transformer,not KWh rating?

5 Answers NTS,

explain the details about vaccum circut breaker and advantages?

4 Answers CPCL, Unisol,

what does a k rating in a transformer means?

0 Answers

when is the Ohms law is applicable?

11 Answers ABB,

whu does the power factor of diesel generator always be 0.8. please explain

5 Answers Dalkia,

In Siemens S7-300 PLC, what is funtion and funtion block ? What is the difference between them ? When to use function and when to use function block

2 Answers

Dear all, i completed M.E(Power Electronics & Drives) 2011 passed out having 78% so i need job in core side but i don't know how can i receive the calls from electrical companies and i uploaded my CV in naukri, times jobs etc.. In that iam not recieved any mails from good companies so give me best procedure plzzzzzzzzzzzzzzzzzzzzzzzz..... Thanks, K.Linga Reddy Email-id:-lingareddykmthm@gmail.com Ph no:-08015402078

0 Answers

For more Electrical Engineering Interview Questions Click Here