what is the name of oil used in transformer

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / madan

11 Answers
23293 Views
Energy Pack, Genco, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

what is the name of oil used in transformer..

Answer / sree

askarel. its a scientific name

Is This Answer Correct ?

17 Yes

1 No

what is the name of oil used in transformer..

Answer / s.jayachandran

Minaral oil

Is This Answer Correct ?

24 Yes

9 No

what is the name of oil used in transformer..

Answer / sreejith

poly chlorinated biphynyle

Is This Answer Correct ?

8 Yes

1 No

what is the name of oil used in transformer..

Answer / rajesh

chlorinated diphenyl is the used in transformer it has has
excellent properties like chemical stability, non-oxidizing,
good dielectric strength, moisture
repellant, reduced risk due re and explosion.

Is This Answer Correct ?

7 Yes

2 No

what is the name of oil used in transformer..

Answer / prashant pate

Its a mineral oil.usually called as POWER OIL.ASKAREL is
synthetic insulating toxic oil used for special transformer
which required non inflamability.

Is This Answer Correct ?

5 Yes

2 No

what is the name of oil used in transformer..

Answer / muhammad asghar

TRI-CHALORO TRI-FLURO METHYLE BENZENE

Is This Answer Correct ?

5 Yes

4 No

what is the name of oil used in transformer..

Answer / naga

elect-roil IS 335

Is This Answer Correct ?

4 Yes

3 No

what is the name of oil used in transformer..

Answer / prashanth.ch

IN transformer Askarel oil used.this oil is only used for
cooling purpose askeral is a
sct.name

Is This Answer Correct ?

4 Yes

3 No

what is the name of oil used in transformer..

Answer / mukesh8243

The name of transformer oil name is

-Dicloro di-floro ethyle benzene.

Is This Answer Correct ?

6 Yes

6 No

what is the name of oil used in transformer..

Answer / vijay

It's a mineral oil.Usually Askarin is used(the spelling may
be different but the pronounciation is somewhat like this)

Is This Answer Correct ?

3 Yes

4 No

Post New Answer

More Electrical Engineering Interview Questions

What is the current carrying capacity of 0SWG,3SWG,10 & 12 SWG solid bare overhead copper conductors?

0 Answers HAL,

why we use end termination kit for ht xlpe cables

1 Answers

if AVR fails in D.G set, what will be the effect?

7 Answers

DG B-check,C-Check,D-check is depending upon the running hrs.If the running hrs is not reached as mentioned.How to conduct the DG checks.

15 Answers Blue Star,

How multimeter shows phase to phase voltage 440V & phase to neutral 220V.

2 Answers

battery capacity use of made?

0 Answers JLL, Shankar Electricals,

What is resistance reading of earth copper rod with grid and without grid?

0 Answers

how to calculate the multiplication factor in HT incomer trivector meters

9 Answers Dalkia, Getco, Gujarat Energy Transmission Corporation Limited GETCO,

Why in KVA diesel engine? Why not KW

3 Answers

I find that underground strip-armoiured,4core,LT PVC cables in an earthed power distribution sytem are occasionly found in charred condition-with no trace of it except ash. Is this because of no proper earth connection/continuity (giving rising to high armour resistance)in the joint enroute or because of insufficient capability (again due to high armour resistance)of cable-armour to carry fault current or due to neglected /unprotected overloading of the cable or due to high armour currents caused by power thefts where only phase(s) are unauthorisely tapped & at the point of poer consumption earth terminal is established by burring underground a not so good earthing rod (or using an underground water pipe for the purpose)

1 Answers

how to calculate units consumption for a 12 hp motor /hr.

0 Answers

Which is stiffer between salient pole rotor and cylindrical rotor synchronous machines? Justify your answer.

1 Answers

For more Electrical Engineering Interview Questions Click Here