Answer / sjtbehera

nominal mix is some fixed ratio of cment,sand, and
aggregate determine by IS code.
ex-M20 is n1:11/2:3
M25- 1:1:2
Design mix is determine by conducting test in lab by
conisedering local avilable material.

Answer / v.purushotham

Nominal Mix:
 Fixed ratio of aggregate-sand-cement.
 Mix to be prepared on volume basis which may leads
under or over- rich mix.
 Not consideration of local available materials.
 Compressive strength of mix was calculated in
laboratory.
 These mixes can be used not more than rich mix
ratio of M20.
 It gives under demanding performance.
Design Mix:
 The Mix designed as available materials locally.
 Cost effective.
 Minimize the material and maximize the strength,
 These mixes are designed for cast in situ.
 These mixes are give high strength and high
performance

Answer / sathish

nominal mix is by volume basis
design mix is by weight basis

Answer / sudiptodas

Nominal
It is the fixed ratio of Cement:sand:coarse
in this case we assume that the cement sand matrix may fill up all the gap between the coarse
in general it comes like
M5=1:4:8
M10=1:3:6
M15=1:2:4
M20=1:1.5:3
M25=1:1:2
as per IS:456:2000
Design mix
in general the cement sand matrix dose not fill the gaps between coarse and thats result more void less strength
to overcome this fact few correction are made to design concert are called mix design
the step of design as follow

*suggested value of stranded deviation
*target strength of mix design
*select w/c ratio with the help of graph etc.
please fined IS:10262:2004 for any further details

Answer / manoj kumar bhola

Simply nominal mix is of volume basis and design mix is done by weight.

Answer / sanjay kumar

Nominal Mix is done by Volume as per Concrete mix and
Design mix is done by Weight,where higher grade of concrete
is require.

Answer / girish negi

Nominal Mixes

In the past the specifications for concrete prescribed the
proportions of cement, fine and coarse aggregates. These
mixes of fixed cement-aggregate ratio which ensures adequate
strength are termed nominal mixes. These offer simplicity
and under normal circumstances, have a margin of strength
above that specified. However, due to the variability of mix
ingredients the nominal concrete for a given workability
varies widely in strength.

Designed Mixes

In these mixes the performance of the concrete is specified
by the designer but the mix proportions are determined by
the producer of concrete, except that the minimum cement
content can be laid down. This is most rational approach to
the selection of mix proportions with specific materials in
mind possessing more or less unique characteristics. The
approach results in the production of concrete with the
appropriate properties most economically. However, the
designed mix does not serve as a guide since this does not
guarantee the correct mix proportions for the prescribed
performance.

Answer / ashwani mishra

nominal mix is said to be laboratory.in which we have
adequate conditions provided.
but design mix can be done in situ or at site where all
necessary condn doesnt prevails.
nominal mix result cant be equal to design mix ever........

CAST EFFECTIVE WATER SUMP CONSTRUCTION DETAIL

0 Answers  

actually dia of the bar reduce asper drawing spacing also decrease that time so how to calculate the spacing of with respect to changed bar dia?

4 Answers   Kamala Group, L&T,

What should be the PH value of water for irrigation purpose

1 Answers  

how to find out spacing inbetween bars instead of 8dia 100c/c to 10dia bars

5 Answers  

I want to construct 1850 square ft of rcc apartment , with stilth parking , the site requires 18 ft of pile foundation , the apartment will be above ground parking , can some one guide me about the cost of construction of such structure in Pune ?

1 Answers  

what is the minimum cement content for M20 & M25 as per is code -456(2000).

0 Answers   PBL,

Where will be the maximum bending moment in a TEE Beam?

2 Answers   Tulip,

there is a residential building L = 20' B = 30' H = 20'  stairs L = 3' H = 20' calculate the numbers of Threads and risers from stairs with formula

2 Answers  

when we select buildup beam

1 Answers  

What is the lap length for tension members if you have 16 dia steel bar and a concrete fc=30.9 and steel grade60 fy=414 mpa

4 Answers   L&T,

for columns reinforcement the lap length is not provided then how to rebar the rods then how rebar should be lapped

4 Answers   Nagarjuna Construction,

HOW WE CALCULATE OR FIND OUT THE DEGREE OF FREEDOM IN A SIMLY SUPPORTED BEAM? IF THERE IS HINGE THEN HOW? & ALSO IN A PORTAL FRAME? PLEASE GIVE A EXAMPLE FOR EACH QUESTION.

1 Answers   CCCL, PSCI,