why the armature coil in dc machine is round??
swagat k.



why the armature coil in dc machine is round?? swagat k...

Answer / seeu43

i think that below answer may be the answer to my
question.i m not sure please answer me.

in dc machine we know that flux from north pole to south
pole asses through the armature coil.if the armature coil
has other shape than sphere then the flux linkig will not
be uniform throughout the surface,so the emf jeneration
will also nonuniform.again sphere aquires minimum area.
so we use spherical or round armature coil.

Is This Answer Correct ?    4 Yes 1 No

Post New Answer

More Electrical Engineering Interview Questions

why a motor rating in KW?

7 Answers   ABG Shipyard,


% voltage variation in distribution a)1% b)5% c)10% d)15%

2 Answers  


being an electrical engineer why you wanna come into software i have an very good academics what answer i have to give

0 Answers  


Type of motor stater detail and working detail

0 Answers  


what is gridrotor resistance starter

0 Answers  






I BOUGHT A HAVELLS ACCL WITH GENERATOR STOP FASCILITY(i.e- BASICALLY IT IS A AUTO CHANGE OVER SWITCH) FOR MY HONDA EXK 2000S HOME GENERATOR (WHICH START IN PETROL & RUN IN KEROSENE). ACCL HAS 8 POINT. 2 FOR MAINS(PH & NUE), 2 FOR LOAD, 2 FOR GEN AND 2 FOR IGNITION POINT(X1 & X2). THE IGNITION POINT IS SPECIALLY FOR AUTO ENGINE STOP WHEN MAINS POWER RESTORE. I CONNECT THIS X1 & X2 POINT TO THE GENERATOR STATER MOTOR & EARTHING POINT. BUT WHEN MAINS FAILS THE GENERATOR COULD NOT START, BUT WHEN DISCONNECT THOSE X1 OR X2 POINT, THEN THE GENERATOR START. BUT WHEN MAINS ON THEN THE GENERATOR SHOULD START, AND WHEN I OFF THE MAINS THE GENERATOR AUTOMATICALLY STOP. PLESE HELP ME HOW I STOP THE GENERATOR AUTOMATICALLY WHEN THE MAINS RESTORE.

2 Answers   Honda,


how to use single phase supply for a three phase equipement.

0 Answers  


how do we fix the rating of mcb required for a specific capacity of the electric motor

2 Answers  


what happens when reactive power increases ? does the reactive power loss increase or decrease ?

2 Answers  


When connecting a loaded powerplant to the Huge grid,what are the factors to be considered and how the VAR flow will affect the system?

1 Answers  


This is urgent!! What is a Thyristor-based 3-ways selector switch with Zero crossing control? how does it operate and where is it mostly found in a system?

0 Answers  


How can we findout the maximum efficiancy of Transformer? At which load?

0 Answers   HAL, Tanfac,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4452)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)