What is the need for modulation?
Answers were Sorted based on User's Feedback
Answer / srikrishna
modulation is neede basically to
i)to increase the bandwidth of the signal
ii)to multiplex the signals
iii)to reduce the interferencemade when we transmit the
signals with nearly same frequency in the audio frequency
range (20-20k)hz.
iv)to favour the complexity of the transmission system
Is This Answer Correct ? | 444 Yes | 75 No |
Answer / radhar
for example if a person is sitting at the bus to go to hyd.
there is a bus which will go to the hyd. it is not the
matter that if the bus goes to the hyd he will also go.
he will also go to the hyd only when he sit in the bus.
here the bus is the carrier & the man is the information.
from this it is clear that modulation is why because the
information which is having less power can't travel large
distances that will put on the carrier which is having
large power that it can travel large distances.
Is This Answer Correct ? | 385 Yes | 74 No |
Answer / sree
1)in shortly it improves the signal strength . means the low
frequency signal can't transmit long distance here low
frequency signal means low strength (weak signal) ,when we
modulate that signal it can be transmitted long distance.
while it transmit long distance i.e., nothing but it's
strength s improves.
2) reduces noise or distortion.
3) multiplexing means we r using frequency translation theorem.
4) we transmit large amount of information at long
distances.i.e., narrow banding the signal.
5) reduce antenna height.
6) we can change the information from one form to another
form. i.e., encryption of data. thats whys we hiding the
information without any hackings.
Is This Answer Correct ? | 256 Yes | 34 No |
Answer / akanchha gupta
some basicneeds are:-
(1)multiplexing
(2)practiability of anteena
Is This Answer Correct ? | 295 Yes | 86 No |
Need of Modulation:
To transfer the message signal from one site another site
without any loss for that we are using modulation.
Modulation classified in three types.
1.Amplitude modulation.
2.Frequency Modulation.
3.Phase Modulation.
Is This Answer Correct ? | 278 Yes | 159 No |
Answer / vignesh.a
Low freq signals can't be transmitted for long distance.
Thats why we are modulating the informtion signals.
Is This Answer Correct ? | 168 Yes | 54 No |
Answer / girija shankar
BASIC NEED FOR MODULATION IS:
1.TO REDUCE ANTENNA HEIGHT
2.TRANSMIT THE INFORMATION TO MORE DISTANCE WITH OUT
INTERFERENCE
3.TO REDUCE BAND WIDTH
EX:SUPPOSE IF U WANT THROUGH A PAPER HAVING INFORMATION TO
YOUR OPP APPARTMENT FROM YOUR APPARTMENT(EX:D=500cm)IF U
SIMPLY THROUGH A PAPER IT WILL NEVER REACH TO THE OPP
APPARTMENT BUT IF YOU USE A STONE.i.e COMBINELY WE CAN
THROUGH BECAUSE STONE HAVE WEIGHT LIKE WISE CARRIER HAVE
MORE POWER THAN BASE SIGNAL THAN WE CAN TRANSMITE THE
SIGNAL.
Is This Answer Correct ? | 136 Yes | 41 No |
Answer / guest
modulation is scheme under which the the signal is first
modified to suitable form(compress or amplied)and mixwd
with the carrier for trassmission
Is This Answer Correct ? | 239 Yes | 185 No |
Answer / kabir
Modulation is a process in which the characteristics of a
signal circuit is caried in accordance with the information
signal which is to be transmitted.
The modulation signal,which is to be transmitted isknown
as Modulating signal.
Need for modulation:
i)multiplexing
ii)practicability of antennas height
iii)frequency conversion
Is This Answer Correct ? | 87 Yes | 36 No |
A channel has a bit rate of 4kbps and a propagation delay of 20msec. For what range of frame sizes does stop-and-wait give an efficiency of at least 50%
0 Answers Chongqing University of Posts and Telecommunications,
dummy strain guage
wat area the advantages of network gateway
One FIU19(E) Flexbus LED is steadily on. What is the meaning? How can a Laptop PC be locally connected to a FIU19E? What is the maximum capacity of a FlexiHopper radio link operated by a FIU19(E), that is equipped with two 4x2M plug- in units? Which of the listed combination of indoor units support
what are the applications of an inverting amplifier?
respected sir, I am Diptiranjan swain have already applied as IFFCO GET ONLINE FORM-2013.kindly,send me one set of previous year question paper.
What is meant by the deflection factor of a cro?
What is the difference between SET and RESET condition or actions?
interrupt controller
why qpsk is done for 45 135225315 not 0 90.270 360 degrees "degrees why "
What is fm transceiver.
I am appearing for SAIL MT TECH ELECTRONICS NEED SAMPLE QP