Answer / aaron sharaon

modulation-it is the process of varing a periodic waveform.
for eg:a tone in order to use that signal to carry a
message. periodic waveform is a sine wave which repeats
itself. normally a high frequency sino sidal waveform is
used as a carrier signal. the three key parameters of a
sine wave are amplitude,frequency,n phase all of which can
be modified in accordance with the low frequency
information signal to ontain a modulated signal.

well uhh....i dont know what is it's need plz check 4m d
above.

Answer / sravanthi mavudi

actually sevaral problems are arived in the propagation of
em waves at AF band(20-20khz)when signal i transmitted with
out modulation.modulation is extreemly necessary in
communication syatems due to following problems.
1.practical length of antenna
2.to reduce noise&interference
3.for frequency assignment
4.for multiplexing
5.to overcome circuit limitations

Answer / ramesh.k

1)To reduce the length of Antenna
2)TO REDUCE EQUIPMENT COMPLEXITY
3)To reduce the bandwidth

Answer / kamaraju

ofter modulation the signal will be more distace and at the
receiver end band width will be adjusted

Answer / nira

Modulation is the process of superimposing the carrier
signal onto the audio or any information signal.If the
process has not been carried out then the information
cannot be recieved without any loss.

Answer / rahul kumar

DEFINITION-
modulation is the process by which some characteristics of a carrier wave is varied in accordance with the instantaneous value of a modulating signal or message signal
NEED OF MODULATION-
1.Practical antenna length
2.operating range
3.wire communication
4.multiplexing
5.to over come equipment limitation
6. narrow anding

Answer / sana

the audio signals are generally in frequency range of
20hertz to 20khz.the length of the antenna required is
quarter of wavelength of signal.for audio signals this
length will be some several kilometers.so by modulation we
are using high frequency carrier to carry information signal

Answer / atul sharma

modulation is the process in which the parameter of a
carrier single circuit in accordance with the information
single which to be transmitted is called the need of
modulation.
1) height of antenna
2)TO remove interference & to multiplexing
3)reduction in noise

Answer / sarath

mixing of less power information with ahigh power carrier wave.
needs..are.,,
1)for reduse the size of antena
2)different brodcasting station to transmit simultaniously at diff carrier frqncies
3)reduce nois and interference
4)for large coverage area

Answer / hikari

1. Reduces the height
of antenna.
2. Avoids mixing of
signals.
3. Increase the range
of communication.
4. Allows multiplexing
of signals.
5. Allows adjustment in
the bandwidth.
6. Improves quality of
reception.

kindly,plesae tell me # the working of BTS # ITS CARDS SPECIFICATION # WORKING OF TRX,DUPLEXER,ASMA CARDS,FIFA # HOW WE ROUTE TRAFFICS # FLOW OF SMS,HOT CALLS,CALLS ETC

0 Answers  

what is the frequency of impulse signal?

12 Answers   Bosch,

Explain to find resistance?

0 Answers  

At what frequency does the IF was fixed?

1 Answers   Astra, Bhel,

i want to question papers of section engineer post (rrb).please sent my mail id .my id is boobalaraja@ gmail.com

0 Answers   RRB,

As a water tank loses heat, the temperature drops by 2 K/min when a heater is on, the system gains temperature at 4 K/min. A two-position controller has a 0.5 min control lag and a neutral zone of ± 4% of the setpoint about a setpoint of 323 K. Plot the heater temperature versus time. Find the oscillation period

0 Answers   Lafarge,

Explain rf?

0 Answers  

The output of a 60hz full-wave bridge rectifier has a 60 hz ripple. It this circuit working properly?

0 Answers  

How micro processor works without internal memory?

0 Answers  

which exam date in wbsedcl in 2009

4 Answers   HAL, wbsedcl,

Explain we take the area of collector wide comparison to base and emitter. Why?

0 Answers  

what is d use of Fascimile?

2 Answers