Answer / bijaleee baba

Any power generating devides are rated as VA and all power
consuming devices (Load) are rated in Watts. For Example :
Inverter / DG are rated in KVA and loads like Bulb / fan /
Electric ketel Iron etc are rated in Watts

Answer / sara

KVA=VI*power factor
Efficiency of DG sets depends on the type of load used. the
manufacturer doesn't know what the type of load(inductive-
lagging-PF, capacitive-leading-PF) is to be used. so they
don't consider the power factor here, they take it as
unity.PF.
KVA=VI*(1) hence DG ratings are in KVA.

Answer / farhan

A generator set is the combination of and engine to create
power and
an alternator to change that power into electricity.

The engine turns a shaft that in turn is connected to the
alternator
This turning of the alternator creates the electrical power.
As there are different types of power all over the world,
different generator sets are built to create different
forms of electrical power.

DG Sets are the Sources which provides power NOT CONSUMING
the power,so KVA determines how much amount of power could
be genertaed from a specific DG Set in short how much the
DG set is capable of creating Amperes at certain voltage
level

For Motors....they are the power consuming devices act as a
resistive/condutive/indudtive load where reactive power is
playing part.....

Answer / santosh

it's not only for DG set, any electrical machine rating will
be in KVA! it's bcos, efficiency of a m/c depends on losses!
at the time manufacturing manufacturer doesn't know at what
powerfactor the machine may be used! AS LOSSES ( COPPER)
DEPENDS ON CURRENT IT TAKES! HENCE THE RATING IN KVA!

Answer / katoch

its ok mr. santosh but why motors rating in KW as motor is
also a machine.

Answer / shaik imtiaz ahamad

because it is independent of power factor as KW is dependent of PF.

Answer / sahil chaudhary

in simple.. there are two types of losses (depending upon load) in dg.. copper losses and iron losses. copper losses is because of current And iron losses is because of voltage load on it.And in other words rating in kva of dg shows the proper capacity of dg with its all types of voltage and current load.

Answer / nitin varia

Generaly Transformer & Generator ratings in KVA because we
use supply from this device
And Motor ratings in KW because we not use supply form this
device

Answer / deepesh dhasmana

KVA rating is given to any equipment which supply electrical
energy, & KW is given to any moter which uses electrical
energy AS IT INPUT

Answer / ananth r

Voltage loss is depend upon the cores (V) and copper losses dependent upon the winding (I). In order differentiate these two things this is not given in KW.

In Power cable specification what is U0/U and Um.

0 Answers  

Define damping ratio.

0 Answers  

What is the method to solve circuit using source transformation?

0 Answers  

How much ampere rating on LT side of distribution transformer and also on HT side of 200KVA transformer

2 Answers   ABB,

How to calculate the current in DG What are the type of power pls explain with related formulas

1 Answers   Corona Enterprises, Sodexo,

tell me about xlpe cable?

1 Answers   IOCL,

Usually in the L & T make MCC feeders' power circuit,we have BMR after the MAIN CONTACTOR.,can we interchange their position, keeping the control logic same???

0 Answers  

Why used IGBT IN AC Drives

4 Answers  

which technique servo motor tested o.k or faulty ?

1 Answers   ABB,

The electrical energy required to raise the tempreture of a given amount water is 200 kwh. If the heat losses are 20%, the energy required is?

0 Answers  

why only 11kv level is used for transmission purpose? why not 230v?

7 Answers  

Why neutral wire is heating in symmetric single phase distribution of three phase power supply?

2 Answers