Answer / p.kithan

Since this system is a non-continuous system and assuming
1.The cooling medium as Air at room temperature
The heat transfer with time can be calculated as,
dq/dt=UA(Ts-T)

WCpdT=UA(TS-T)dt

on integrating,

Time taken (t)=WCp\UA*ln((Ts-T2)/Ts-T1))

q=Heat transfered,w=weight of water,Cp=specific heat of
Air,Ts=saturated temperature of air,T1=temp of water at
initial,T2=temp at final,A=area of heat transfer.
U=over all heat transfer coeffcient(assume for water,ref-
perrys)

how did you spend today

0 Answers  

---

Explain the factors involved in considering the choice of dry screw compressor?

0 Answers  

---

What are the steps required to design a vapor-liquid separator or flash drum?

0 Answers  

---

According to Shockley equation, the I – V characteristic of a diode is approximated by I = IS [ exp (nVD / VT) – 1 ]. For silicon, let the reverse bias saturation current IS as 0.000000000001. If n is ideality factor with value of 1.5, VT as thermal voltage drop of 0.026 V at room temperature, what is the value of current I that passes through the silicon diode in the heater of evaporator when the forward voltage drop VD = 0.026 V? Please take note that exp is the exponential function with e(1) = 2.718, e(2) = 7.389.

1 Answers  

---

NATURAL GAS ENGINEERING - QUESTION 26.1 : (a) In natural gas pipe sizing, the length of the pipe from the gas source metre to the farthest appliances is 60 feet. The maximum capacities for typical metallic pipes of 60 feet in length are : 66 cubic feet per hour for pipe size of 0.5 inches; 138 cubic feet per hour for pipe size of 0.75 inches; 260 cubic feet per hour for pipe size of 1 inch. By using the longest run method : (i) Find the best pipe size needed for the capacity of 75 cubic feet per hour. (ii) Estimate the suitable range of capacities for the pipe size of 1 inch. (b) The maximum capacities for typical metallic pipes of 50 feet in length are : 73 cubic feet per hour for pipe size of 0.5 inches; 151 cubic feet per hour for pipe size of 0.75 inches; 285 cubic feet per hour for pipe size of 1 inch. By using the branch method find the best pipe size needed for the capacity of 75 cubic feet per hour when the length of the pipe from the gas source metre to the appliance is 52 feet.

2 Answers  

---

In differential centrifugation of cells with diameter D in centimeter, the square of D is given by D x D = [18n ln (RF / RI) ] / [ (RP – RFF) Wt ] where n is the fluid viscosity (poise), RF is the final radius of rotation (cm), RI is the initial radius of rotation (cm), RP is cell density (g/ml), RFF is the fluid density (g/ml), W the square for the rotational velocity in (radians / s) (radians / s), t is the time required to sediment from RI to RF (s). Derive an equation for W as a function for D, n, RF, RI, RP, RFF and t, with the stated units above, in radian

1 Answers  

---

How can one determine the particle size distribution for a given bulk solid?

0 Answers  

---

Question 109 - (a) Acceptable wavefunction in quantum mechanics in the range of : negative infinity < x < positive infinity, vanishes at least at one boundary. Which of the following is the wavefunction or are the wavefunctions of acceptable theory : P = x, P = | x |, P = sin x, P = exp (-x), P = exp (-| x |)? State the reason. (b) Let linear momentum operator P = -ih d / dz. The wavefunction is S = exp (-ikz) where i x i = -1, k and h are constants. Find the linear momentum of such wavefunction by using the term P x S.

1 Answers  

---

What are some guidelines for designing for liquid and gas velocities in process plant piping?

0 Answers  

---

What is Draft? It releavent to furnace.

1 Answers  

---

plz somebody send me the latest placement papers of hpcl graduate trainee post.....at bikash.mallick1@gmail.com

0 Answers  

---

pls send me HPCL & reliance test paper for chemical engineering.....

4 Answers   HPCL, Reliance,

---