Answer / jitendera kumar sinha

ok
thanks for the complement that my answers are easy to
understandble

now comes on topic subnating
brekaing a single network in to the multiple subnetwork is
called subnating
sub+nat+doing=subnating(trick for rember the diffination)
why we need it-
in that decade where all the industry and corporte are
being comptrized but for the comunicatin on the n/w channel
it is nessry that all ip address should be unique so
maintain the uniquecity of that ip address subnating is
used
this is the technical explanation if some one say that
scince ip addres is not enough so to preserve the ip
address we did subntaing this is also wright but not a good
approch
this is all about theroytical consepts of sunating
now how we done it

here it is(i am reqesting you to write it some where becoz
it is the back bone of networking)

now as you know that threr are classes of ip address

as class a range of class a 1---126 mask 255.0.0.0

class b range of class b 128--191 amsk 255.255.0.0

class c range of class c 192--223 mask 255.255.255.0

class d range of class d 224-255 mask 255.255.255.255

class e range of class e
here some point you should remebr
1 in class a i didnot define 0 and 127 because 0 is resved
for default root (you will read it in routing protocol)amd
127 is reseved for loop back(familar with 127.0.0.1 for
checking nic card stautush wright if not then try it to cmd
promt )
2 network 224 - 239 resved for multicasting and class e 240-
255 for some defence uses
so not be confused becoz network 224 to 255 are reseved for
class d and class e addresss

now let start subnating with class c adress

class c address
in that adress 3 octet are for the networking and 1 octet
for host
that is
class c N|N|N|H
each n/w bit represnted by N
and host bit by H(plz keep in mind/i will use it in that
whole article)
ok each network bit coantin 8 bit
and each host bit conatin 8 bit
then if threr is ip asrees 192.168.10.12 then what should
be mask
answer is 24
now question is what is mask
mask is used to identyfing that from which class ip address
so come to th point
ip address=192.168.10.12/24
now why 24?
becoz in class c ip address there are 3 octet for network
of size 8 bit then 8*3=24.so what did you notice that for
identyfing the ip address class we see the only value of
first octet only first (remeber)

so in the subnating we answered folowing question
1 how many subnet does the chosen subnet mask produse
2 how many vallid host per sunet are avilable
3 what are the brodcast address of each subnet
4 whta are the valid host in each sunet
5 what are the valid sunet

befor doing sunating these two equation must be rembred
that is
2^n-2=for total nuber of network n=network bit
2^h-2=for total number of host bit h=avilable host bit
why -2(becoz cisco not recomnded it as a valid n/w and host)

let understand by an exapmle
192.168.10.0/26

ok what should be original mask for that address
answer is
192.168.10.0/24 but given mask is 26 that is we need 2 bit
extera from where we get it
we get it from hot bit becoz it has 8 bit for host
now we borrow 2 bit from host then remnaig bit are 6
so how many n/w soory vallid network =2^2-2=2
and what is the nimber of valid host=2^6-2=62 host per sunet
now what should be mask of that given ip address
herer it is scince we borrow two bit from host for n/w then
128 64 32 16 8 4 2 1 (what is this?=this is some thing to
convert any decimal value to binary in eifght add all u get
255)
again i wrote 128 64 32 16 8 4 2 1
1 1 0 0 0 0 0 0
two bit is taking for sunating so i amrk two bit as one and
rest are as 0
so add this two bit marken by 1
128+64=192
then mask of that given ip will be
255.255.255.192/26(see that mask i decriebed)
so what should be block size
tha is 256-192=64
that is subnated ip address is
192.168.10.0 192.168.10.63 192.168.10.127 10.191
----------- ------------ ---------- ------
----------- ------------ --------- ------
192.168.10.63 192.168.10.126 192.168.10.190 10.255

what is n/w id=first ip address is always known as n/w id
what is broadcast id=last ip address is broad cast id
for given ip 192.168.10.12/26 what is the n/w id and broad
cast id
answer os n/w id 192.168.10.0
broad cast id 192.168.10.63
simalry for192.168.10.92 what is the n/w id and broadcast
id
answer is 192.168.10.64(n/w id)
192.168.10.126(brad cstid)
ok here cisco let the invalid ip the first one and last one
that is
192.168.10.0---------192.168.10.63
192.168.10.191 -----192.168.10.255
valid host
the ip address between the n/w id and host id
so herer is your task
in need reply
wsunat that ip address
192.168.56.64/27
and answer all short of thing

after that i will go to next section

Answer / jitendera kuaar sinha

hi arshad
here is expalnation
i have mistaly write next sunet id that is
192.168.10.0 192.168.10.63****( my mistake it start
from (192.168.10.64)
----------- ------------
----------- ------------
192.168.10.63 192.168.10.126

if this is your point of confusion then i ma soory i donot
know how i have writenn it.

now how to detrmine the exact block size and what will be
next sunet id(it also called n/w id)
then i am going to explain again
what was the given ip address
192.168.10.0/26
ok 2 bit of subnating i.e two bit is taken from host bit
i.e

128 64 32 16 8 4 2 1
1 1 0 0 0 0 0 0
tha is two bit is taken from host
now how many n/w will be made 2^2-2=2(acording to cosco
nither 4)
how many bit for host it is 6
numer of host / sunet=2^6-2=62
what is the mask of that given ip
255.255.255.192
what is the block size=256-192=64******************
block size consern with how many ip address should be
reside in the single n/w pool
that is therer is 64 ip address reside in the pool.now if
we started it with 0 than 64th ip address is end with 63
count 0 to 63 how many bit is it 64 if not then count again
(kidding)ok
so one pool is end with 63 then next pool with started at
what is it 64? yeas and go the 127 again 64 host
now any confusion?
the try to solve that question which i have provide and
there is another probem i am providing try to solve i am
90% sure you canot but try?


what is the n/w id and the brodcast id for the ip address
192.168.10.56/27

try it then i wiil send the tutreala about vlsm design in
claas c

scince first one is n/w id the last one is broadcast id
then vallid host ip address is 62(see the formula)

Answer / asad

Hi Jatendra thanks for such a nice tutorial.....

but i feel a little confusion in this step

192.168.10.0 192.168.10.63 192.168.10.127 10.191
----------- ------------ ---------- ------
----------- ------------ --------- ------
192.168.10.63 192.168.10.126 192.168.10.190 10.255

In this how take start from ..10.63 and after that increment
64 each time. my point is 63. how we know that the first
address of subnet will start from .63 .plzz clear this one

Answer / shridhar

what is the n/w id and the brodcast id for the ip address 
192.168.10.56/27.

192.168.10.32  N/W ID
192.168.10.63  B/C ID

Name the command we give if router ios stucked?

0 Answers  

---

Tell us the name of algorithm of eigrp protocol?

0 Answers  

---

What is the total bandwidth of all channels on a BRI circuit? A. 56 kps B. 64 kps C. 112 kps D. 128 kps E. 144. kps

5 Answers   Infosys,

---

What is true when using DDR? A.) HDLC is the preferred encapsulation B.) You must use static routing C.) You should use dynamic routing D.) You should use ISDN

1 Answers  

---

Identify the 2 commands that will display the status and information about interface E0 only? A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.) show interface

1 Answers  

---

---

A server is running HTTP, SMTP and DHCP. Which of the following best explains how the server is able to handle all three services over the same connection? The server has separate buffer areas for each application and forwards all data to each service. If the data does not apply to that application, it is discarded. The server processes each packet one at a time and forwards the data to the application that indicates that it is waiting for a transmission to arrive. The data is discarded if it does not apply to that application. The server uses the destination port number in the TCP/UDP header to identify the service. The data is forwarded to the service identified by the port number. The server uses separate three-way handshake connections to control the flow of the data and relates the service to the proper connection. This relationship allows the server to pass the data to the proper service.

1 Answers  

---

In stp which protocol is used for detrming root port root bridge ,forwarding port and blocking port

1 Answers   IBM,

---

let threr are three router 1 is cionected to two and two is conected to three that is 1----2----3 now we can ping 2 from 3 and 1 to two but we are not able to ping 1 to 3 let router 1 is local and rest of two are remote what should be urs troubleshoot steps

2 Answers   Volvo,

---

What is a Frame Relay?

0 Answers  

---

Dear Mr. JITENDERA KUAMR SINHA how are and how is your family? Anyway can u send me your personal email address?

4 Answers  

---

In configuring a router, what command must be used if you want to delete the configuration data that is stored in the NVRAM?

0 Answers  

---

- What is EGIRP and IGRP - How EGIRP and IGRP works

1 Answers   Airtel,

---