Answer / satyanaraya na

Wear rings can be defined as a device used to seal the
pressure leakage of the liquid between the inlet of the
impeller and the pump casing. Wear rings are typically
found on pumps with closed impellers. A similar device that
serves the same function called a wear plate can be found
on some pumps with a semi-open impeller.
The typical reason for using a wear ring is to decrease the
amount of leakage loss around the impeller. Due to more
work available to push the pumped liquid out the discharge
there is a slight improvement in pump efficiency.

And also as name indicates 'WEAR' which is a ring can
sacrifice its size by taking friction generated between
stationary and rotating elements.
The replacement of rings is easier & cheaper than replacing
impellers/casing.
Hope this is clear.

Answer / m.saravanaraj

A clearance between the pump casing and impeller is
required for free rotation of the impeller,if the clarance
is more between them,there is some possibility of water
leakage from the high discharge to suction side which
ultimately reduce the efficiency of the pump performance
and the leakage water will cause corrosion.In order to
avoid these problem a wear ring is incorporated in the pump.
In total the purpose of wear ring is to prolong the
life of the pump casing and impeller

Answer / pushkar

They are used as the seal between casing & impeller

Answer / rajesh singh

mainten the clearence witbeen impelor and casing and
restrec the liquid from high to low pressor side.and
increes the epiciancy of pump.

Answer / m.m.boopathy

To reduce pump maintenance and costly repairs of impeller
and casing a replaceable wear rings are installed in the
centrifugal pumps,which allows a small running clearance
between pump impeller and casing.

Answer / gautam

there is a small clearence maintained between impeller nd the casing, so that impeller can rotate freely.Now there is a small amount of liquid leaking from discharge side to suction side causing erosion of the parts near clearence,causing this clearence to increase. so casing wear rings are provided to minimize these clearence nd take up the erosive action of leakage fluid on itself rather than letting the impeller or casing to be eroded. Now as casing wear rings are cheap they can b replaced by new one if it has worn out enough.

Answer / ajit kumar sahoo

Pump is a hydraulic machine.wearing is a seal between the casing and impeller .it life span is increased life span of the pump casing and impeller when the clearance is too high between the casing and impeller it need to replacement. Engg mechanical

Answer / rehan

All the answers are correct for casing wear ring. However no one has explained the difference between impeller wear ring and casing wear ring.

Answer / rajeev singh

Dears,
First sorry for speling mistec.

Ans.- 1. cost factor.
2. keep safe of our casing and impeller.
3. Mainten the clearance beetwin impeller and casing.
guys we can mainten the clearenc without wearing
but think, you wich one esey reples the wearing
or, impeller and casing.

Rajeev Singh
Mechanicial Tech.
SAUDI KAYAN (KSA)
C.W.S

Answer / ravi

Wear rings are not part of all the pumps. The wear rings
are found in larger size of the pumps & split case pumps

A vertical plate and a horizontal plate are suspended in an open room. Both are heated to the same temperature. Which one will cool first?

11 Answers   BARC,

what will happen if there is no expansion valve in the air conditioning system? is there any possiblities of working an AC system without expansion valve?

4 Answers  

what are engines that use carburetor and that use inductor ? difference between them

6 Answers  

What is machine

6 Answers  

"In electricity, what is commutator? Carbon brush? "

1 Answers   RRB,

What is a manometer and give an example of its application

1 Answers   RRB,

What does a pump develops? Flow or Pressure. Give the Answer with Proper Logic.

22 Answers   Essar,

what is the technology used in sap?

0 Answers   InFocus, Infosys,

What resistance the ship encounter when the vessel is at sea

0 Answers   RRB,

hi this is swaroop i appliled for masters in us for mba and my ielts score is 5.5 and no gre and i have 14 backlogs

0 Answers  

what is critical temprature discuss that is any pressure greater than critical pressure is valid for boiler design.....2 in what cycle steam power plant is based draw h-s diagram.different process to make gear what is tooth profile what is generatic and directric and many more as i m doing mtech thats why interview was of 30 minute...........

0 Answers   DVC,

1.an you please send all INTERVIEW Unigraphics/ansys QUESTIONS&ANSWERS. structural analysis,linear,nonlinear analysis,modal,harmonic analysis all questions @answers? Send all typical HR questions &answers?

3 Answers   Kennametal, Sandvik,