Interested to Buy Any Domain ? << Click Here >> for more details...
Sparking occur when a load is switched off because the
circuit has high
a.) Inductance b.) Capacitance c.) Resistance
d.) None
- 14 Answers
- 43979 Views
- Biwta, BSNL, CDS, DMRC, Infosys, SSC, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / kondapallisirivarsha
inductance ....since...resistance becomes zero....high
currents flow through the whole circuit...so heavy heat&
sparks r produced
| Is This Answer Correct ? | 19 Yes | 4 No |
Answer / srikant
When we suddenly switched off a load due to sudden change in current a voltage is developed across the inductor(v=L di/dt). This heavy voltage will ionise the air to make the air as conductor to produce arc in the form of sparking.
| Is This Answer Correct ? | 9 Yes | 0 No |
Answer / sameer manas
Because
Inductor does not allow sudden changes
| Is This Answer Correct ? | 7 Yes | 1 No |
Answer / gayathre
As we switch off the circuit, there is a sudden change in the magnetic flux linked with the circuit.This might be the reason for the spark. And this leads to the answer.
| Is This Answer Correct ? | 3 Yes | 0 No |
Answer / niloy datta
there must b some other reason... because for AC it always
changes from +ve max. to zero and from zero to -ve max. and
with this principle transformer inductor core works with ac
only. So what u indicate by sudden change..
and when the load is switched off, I think it gets infinite
resistance not the zero resistance...
so please clarify..
| Is This Answer Correct ? | 5 Yes | 3 No |
Answer / sanjay yadav
Well I think the reason of sparking is high resistance in load circuit .forexample:we can practically see in our home that when we connect or disconnect a 2000kw electric heater to electric circuit,a large numbers of sparking occurs because flow of current (electrons )depend upon resistance. When we connect or disconnect a high resistive load,some current electrons misguide and they jump into air and strike to air electrons,and its result is sparking occurs. Inductance is a not a reason for sparking because when we connect a 25kva 3 phase transformer without load on line there is no sparking occurs on terminal,this is my personal experience.
| Is This Answer Correct ? | 7 Yes | 5 No |
Define virtual ground in the op amp?
What is cache coherency and snooping
GET-2013 exam is going to be held on which day(tentatively).
What are the main components of AMF panel. Is it required to use ATS in LT panel if DG is used as stand by supply? Please send any single line diagram showing AMF & LT panel etc., if possible please send to sreenu_207 @ yahoo.co.in
i am preparing for AAI JR EXECUTIVE exams so plz suggest the objective materail for preparation
0 Answers AAI Airports Authority Of India,
what is lvdt?
In 7-segment display system, zero blanking is used to blank out A All the leading zeros B All the trailing zeros C The zero in the MSB(location) D a and b
What is a sequential circuit and what is a combinational circuit?
what is a bleeder resistor?
What are the processes required to perform interfacing successfully?
1) is external oscillator XTAL1 &XTAL2 connection must needed ? 2) shall we proceed without oscillator for simple logialoutput
0 Answers Jayam Engineering Works,
what current is transistor biased?
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
