1 bar is equal to how many pound per square inch(psi)?

Categories >> Engineering >> Instrumentation
Suggest New Category

Question Posted / eswar

14 Answers
38512 Views
Essar, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

1 bar is equal to how many pound per square inch(psi)?..

Answer / anirban

1 bar= 15 psi(correctly it is about 14.5037744 psi)

Is This Answer Correct ?

128 Yes

12 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / naresh yadav

1 kg/cm2 = 0.98 bar
1 kg/cm2 = 14.7 psi

Is This Answer Correct ?

70 Yes

19 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / tauqeer

1 bar = 14.5 psi

Is This Answer Correct ?

65 Yes

14 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / praveen kumar

1 bar = 14.5 psi

Is This Answer Correct ?

31 Yes

16 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / faisal haroon

1bar=14.504 psi

Is This Answer Correct ?

6 Yes

1 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / raffi

14.636 psi

Is This Answer Correct ?

14 Yes

10 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / umeashwaran

14.50377 psi

Is This Answer Correct ?

6 Yes

3 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / rizwan

1 bar=14.7 psi

Is This Answer Correct ?

28 Yes

26 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / faiyaz ahmad

14.7 parts per square inch

Is This Answer Correct ?

0 Yes

1 No

1 bar is equal to how many pound per square inch(psi)?..

Answer / faiyaz ahmad

14.7 pounds per square inch

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Instrumentation Interview Questions

generally transmitter power supply having some range(12v to 35v) but the out put(4-20 mA) must same for given input.If we vary the power supply voltage then output mA also to be change according to V=IR. Is there any voltage regulator in the transmitter ?

2 Answers

yokogawa Temperature transmitter showing Error 15 which is Reverse Cal Fail (confirmation calculation result is bad) in manual they mentioned reasion That the output goes to the value set by hardware failure mode jumper. How can solve this problem ? anybody can say solution

1 Answers GTL,

How will you select suitable Instrument for Process line/Tank/Vessel?

5 Answers

Can anyone provide me the details of GAIL test paper?What is the format and what type of questions will be there? my id-princegnb@gmail.com

1 Answers GAIL,

how many types of thermocouple cable are? give the name of each type.

1 Answers Fabco,

what is difference between venturi and orifice

1 Answers

how to calibrate the temprature transmitter MURCREYtype and thermocouple input type.

1 Answers Shree Cement,

calculate the rane of level use of this values, h=3 meter density=0.9 , whats the rang?

2 Answers

Describe all types and levels (4-20mA, 0-10V, mV, pulse, etc.)of analog and digital I/O used in process control application.

2 Answers Jindal,

TEMPERATURE VARIATION FOR FREQUENTLY.

0 Answers TVS,

how can check the loopchecking for valves?

3 Answers

while am calibrating Drager polytron 2IR flame gas detector occured non zero status.how can i get zero status?

0 Answers Gasco,

For more Instrumentation Interview Questions Click Here