What is the diffrence between four strock and two strock ic
engine
Answers were Sorted based on User's Feedback
in four stroke engine two revolution crank shaft one power
stroke will be produced.
in two stroke engine one revolution crank shaft one
power stroke will be produced.
| Is This Answer Correct ? | 68 Yes | 4 No |
Answer / abhilash
in 4 stroke engi crank revolutes two time and one power
stroke be produced
that to in 2 stroke engi one revolution made bye the crank
shaft and one power stroke is occured
| Is This Answer Correct ? | 39 Yes | 3 No |
In 4 stroke engine - one cycle of operation (suction,
compression, power, exhaust) completes in 720 degrees of
crank shaft or fly wheel rotation.
In 2 stroke engine - one cycle of operation (suction,
compression, power, exhaust) completes in 360 degrees of
crank shaft or fly wheel rotation.
| Is This Answer Correct ? | 23 Yes | 1 No |
Answer / abhishek kapuria
For 4 stroke :
a. Valves are used.
b. Heavy flywheel is used.
c. Thermal efficiency is high
d. For two revolution of crankshaft one power
stroke is produced.
For 2 stroke :
a. Ports are used.
b. Lighter flywheel used.
c. Thermal efficiency is low in comparison to $ stroke
d. For one revolution of crank shaft one power stroke is
produced
| Is This Answer Correct ? | 20 Yes | 1 No |
Answer / harsha
1.ports r diffrent in either engines.
2.fuel consumtion is more in two strock engine & it cause
more pollution than the four strock engine.
3.fuel is completely burnt out in four strock engine but
not in a two strock
| Is This Answer Correct ? | 13 Yes | 1 No |
in four stroke the combustion cycle is completed in four
cycles whereas in two stroke combustion si completed in two
strokes
| Is This Answer Correct ? | 13 Yes | 6 No |
Answer / shiv shanker gupta
In 4 stroke engine - one cycle of operation (suction,
compression, power, exhaust) completes in 720 degrees of
crank shaft or fly wheel rotation.
In 2 stroke engine - one cycle of operation (suction,
compression, power, exhaust) completes in 360 degrees of
crank shaft or fly wheel rotation.
| Is This Answer Correct ? | 10 Yes | 3 No |
Answer / m.perumal
foure stork engine: suction, copution,power,exhasutfor four
strok only in crank shaft two revelution, so one power
strok got it.
two strok engine:suction, copution,power,exhasut for crank
shft one revolution,so one power stok got it.
| Is This Answer Correct ? | 8 Yes | 2 No |
Answer / mahesh chaurasia
in four stroke engine two revolution crank shaft one power
stroke will be produced.
in two stroke engine one revolution crank shaft one
power stroke will be produced.
in 4 stroke engi crank revolutes two time and one power
stroke be produced
that to in 2 stroke engi one revolution made bye the crank
shaft and one power stroke is occured
| Is This Answer Correct ? | 2 Yes | 0 No |
how did you go into the mechanical engineering
Mention some of the major contributions made by you in your present and previous jobs:
From where i can get cds about mechanical related subjests
What is long form of FIAT
which bearing use in lathe spindle
What are the requirements of a good fuel?
what is the calculation of selection ofan capacity is 12000m3/hr.
How much is the specific fuel consumption of an average diesel engine?
Why is Air Conditioner capacity measured in ton like 1.5ton?
What is pulse tube used in low temperature application?
what is there in altenator which produces electricity?
How do you find ductile-brittle transition temperature of metals?
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)