what are the types of sus station ?
Answers were Sorted based on User's Feedback
Answer / pyobik
Sub-Station classification:
1. According to service requirement
a) Transformer sub-station
b) Switching sub-station
c) power factor sub-station
d) Frequency changing sub-station
e) Converting sub-station
2. According to constructional features
a) Indoor sub-station
b) Outdoor sub-station
c) Under ground sub-station
d) Pole mounted sub-station
| Is This Answer Correct ? | 45 Yes | 2 No |
There are mainly three types of sub-stations.
1.step up/down substations-where stepping up or stepping
down of voltage has done.
2.power factor improvement sub station-where power factor
is improved by installing capacitor banks or synchronous
condensors.
3.switching sub stations- Where switching action like
switching on or off has done for maintenance purposes for
other reasons.
4.poll mounted substation, Underground substation
| Is This Answer Correct ? | 31 Yes | 4 No |
There are mainly three types of sub-stations.
1.step up/down substations-where stepping up or stepping
down of voltage has done.
2.power factor improvement sub station-where power factor
is improved by installing capacitor banks or synchronous
condensors.
3.switching sub stations- Where switching action like
switching on or off has done for maintenance purposes for
other reasons.
| Is This Answer Correct ? | 22 Yes | 9 No |
Answer / rvg.msceb
These are main types of sub-stations.
1.at generating stations: step up voltage to higher level
2.at intermediate stations: step down voltage to lower level
say 400Kv to 11kv, and power factor improvement may be also
doing within these sub station
3.At load center: Where voltage is getting down to 400volts,
and this is near to be load center
| Is This Answer Correct ? | 12 Yes | 2 No |
Only two types.
1. Indoor substation
2. Outdoor substation.
| Is This Answer Correct ? | 12 Yes | 3 No |
generally four types of substation.thes are
Step-up Transmission Substation
Step-down Transmission Substation
Distribution Substation
Underground Distribution Substatione are
| Is This Answer Correct ? | 8 Yes | 0 No |
Answer / vijendra joglekar
Types of sub station:
1)Pole mounted type sub station
(for low rating up to 100 kvA)
2)Outdoar type sub station
(for voltage upto 11kv to 132kv)
3)Indoar type sub station
(for voltage local sub station primary voltage
11kv,secondary voltage 400/440 volts)
| Is This Answer Correct ? | 6 Yes | 0 No |
Here are the diffrent kind of substation.
1. Step up / step down substation
2. Power factor improvement substation
3. frequrecy changing sub-station
4. HVDC substation.
5. Outdoor substation
6. Indoor Substation
7. Grid Station ( Regional , National )
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / r.ramadhivya
1.Generating substation
2.grid substation
3.secondary substation
4.distribution substation
5.special purpose of substation
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / gayatri
type of sub-station
1. outdoor sub-station
a) pole mounted sub-station
b) foundation mounted sub-station
2. indoor sub-station
| Is This Answer Correct ? | 4 Yes | 0 No |
in my industry we are using 3 step up transformers for induction heaters..i.e 415/580v and other are 11/440v.in power consumption does a step trnsformer makes any difference compared to step up?? plz explain
why to use 50hz only in tansmisson and as well as in distribution why not60hz?
For testing 33kv cable hipot testing. How much kv we have to Apply .Give in details.
What is the minimum permissive IR value for LT & HT motor for safe starting?
What is the Frequency while we step up the voltage from 220V to 11KV? Is it possible? Explain it?
How to control speed of DC motor with AC power?
what the effect will occur if we increase the airgap in induction motor
how dia of wire and angles are calculated for overhead shielding wire to protect substation equipment from lightening strokes???
How to calculate the current in DG What are the type of power pls explain with related formulas
1 Answers Corona Enterprises, Sodexo,
I have 12MW gas engine based power plant its running parallel with grid. my problem is When cpp run in island mode(without geb) that time geb transformer power factor is 0.2 lagging. When cpp run with parallel that time power factor is 0.94 lagging So how can i maintain power factor ofgeb transformer in island mode 0.9 lagging?
what is the use of choke on tube light fitting
37 Answers Bhel, Dharma, HSBC, TCS,
definition of transformer
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)