Interested to Buy Any Domain ? << Click Here >> for more details...
what is the difference between rake and rack.
- 13 Answers
- 22389 Views
- Bhel, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / karthick
rake is an angle given to the tool to guide the chip
movement whereas rack is a gear used with pinion to convert
rotary motion into linear and vice versa..
| Is This Answer Correct ? | 17 Yes | 1 No |
Answer / nageswara rao
all above answers r wrong...
rack is nothing but ordering of tooth...
rake is an angle..of tool..
| Is This Answer Correct ? | 13 Yes | 1 No |
Answer / malayappan
Rake is angle of tool. If you take a sing point cutting too
like a turning tool of a lathe it has front rake angle,
back rake angle and side rake angle and all are necessary
for improved machining and geting relieved the chip that is
coming out. In fact all these angle vary they are not same.
Rack may be a shelf you have in your house or ordering of
too the as said in a earlier answer
| Is This Answer Correct ? | 8 Yes | 0 No |
Answer / rakesh
rake is the term used in case of a single point cutting tool
for operation like turning in lathe.
It is the angle between the normal to the machining surface
and the rake face of the tool.
-Higher the angle will decrease the cutting force and
increase the surface finish of the workpiece,
-This angle can be from 0-90 degree ,but generally its
recommended to 15-30 degree rake anle(back rake angle).
-Because increasing the rake angle,removes the material from
the tool that will support the cutting edge of the tool and
help in heat distribution from the tool to the atmoshpere.
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / varun
rake is the angle of single point cutting tool and rack is the small portion of the gear which has an infinitely large number of teeths for example rack and pinion
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / harimec02
rake is cuuting angle and rack is one type of gear
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / guest
rake is the cutting tools one of the angle, rack is the one
of the gear which transmitte rotary motion to linear motion
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / avi
one rake is cutting tool angle, and another one rack is a gear with infinite pitch circle rad or we can say it is a straight toothed gear like used in lathe machine..........
| Is This Answer Correct ? | 0 Yes | 0 No |
Explain how pipe flanges are electrically insulated?
During the ISO/TS Certification Audit the auditor arise the NC in the MRM dept.The NC is MRM is not conducted effectively . What is the CA for that NC?
How do we differentiate oxy & acetylene?
What is an expansion valve and its purpose?
What is vane diagram in centrifugal pump?
what happens at an equipment buyoff?
Why should we hire you over the others waiting to be interviewed?
y the unit of torque Nm not called as joule
When effect of variations in specific heats is considered then how do maximum temperature and pressure vary compared to air standard cycle ?
An Fuel Tank in circular in shape as 1500mm in dia and 1000mm in length placed in an horizontal position, its possible to find the fuel capacity of tank
If any changes done in the process of production what that is called.
if you are standing on 30th floor & you asked to drink a water through straw .can you? water is in glass at the ground floor.
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
